background image

MODEL 7748 SINGLE CHANNEL RS530 DB25 A/B SWITCH W/CUTOFF, TELNET AND GUI 

 

Electro Standards Laboratories, Inc.  

                      (401) 943-1164       

www.electrostandards.com         - pg 8 -                                  Pub. 4703-02 

 

OPERATION 

The Model 7748 can be operated either by the front panel or through its 
Remote port.   

Figure 2: Model 7748 Front Panel 

 

Manual Control 

The front panel view of the Switch System is shown in the above figure.  
On the front of the switch are the following controls and indicators: 

  A, B INDICATORS

 – Red LED’s indicate the switch position as 

well as the power status. 

o

 

The LED in the steady state indicates the position of 
the switch. 

o

 

If the front panel pushbutton is locked and the button 
is pressed, both LED’s will light until the pushbutton is 
released. 

o

 

When first powering up, both LED’s will light and flash 
during the power up routine. 

o

 

If the Remote Ethernet port is reset on power up, both 
LED’s will light and flash a few times for several 
seconds until completing its routine and displaying the 
present position. 

  MANUAL PUSHBUTTON

 – The front panel pushbutton allows 

the switch position to be changed. 

o

 

Depressing and releasing the pushbutton allows the 
user to toggle the switch position. 

o

 

Pushbutton control can be inhibited if locked out 
remotely. 

o

 

Pressing and holding the pushbutton on power up will 
initiate the Remote Ethernet port reset routine. 

Model 7748 Front Panel 

Pushbutton and LED’s 

Summary of Contents for 7748





























Reviews: