background image

704 North Clark Street

Albion, MI 49224 USA

 Tel:   (517)629-5990

Fax:   (517)629-6690

E-mail:  info@sepatriot.com

Web site:  www.sepatriot.com

ANTENNA SYSTEMS

ANTENNA SYSTEMS

INSTALLATION &

ASSEMBLY INSTRUCTIONS

1.8M MVSAT Antenna

 

Electrical RF 

 

Receive 

Transmit

 

Frequency  

 

11.7-12.75 GHz 

14.0-14.5 GHz 

Gain (Midband) 
  

 

R/T 

 

45.3 dBi 

46.7 dBi 

    

4-Port 

 

45.2 dBi 

46.6 dBi 

 VSWR   

 

 

 

1.30:1 

Beamwidth (degrees) 

     

-3 dB 

 

.91 

.77 

     

-15 dB 

 

1.91 

1.62 

First Sidelobe Level (Å2 dB) 

 

-20 dB 

-20 dB 

Radiation Pattern 

 

Meets FCC requirements for 2° Spacing 

Antenna Noise Temperature 

     

10° Elevation Angle  

43°K 

Polarization    

 Linear 

Linear 

Power Handling Capability 

 

 

1KW per port 

Cross-Pol Isolation 

   

On-Axis 

 

35 dB 

35 dB 

  

Off-Axis (within .5 dB BW) 

25 dB 

26 dB 

   

Off-Axis (within 1 dB BW) 

22 dB 

24 dB 

Feed Port Isolation  - 4-Port Feed 

   

RX/RX 

 

30dB 

   

TX/TX 

 

30 dB 

   

TX/RX 

 

60 dB 

60 dB 

   

Controller

 

RC3000A    

 

Full-function controller with opt. GPS and Flux-Gate  

Size 

 

 

 

Two rack units high

 

Input Power 

 

110V AC, 1 ph, 60 Hz, 15 amp 

 

 

Mechanical

 

Reflector Type 

 

1.8M Prime Focus Offset 

Mount Geometry 

 

Elevation over Azimuth 

Polarization  

 

Rotation of Feed 

Travel  

Azimuth   

 

270° for 2-Port, 240° for 4-Port 

 

 

 

 

400° Optional for 2-Port or Feed Boom Mounted HPA 

Elevation 

Operational 0-90° or 0-65° of reflector boresight 

Total  

0-160° 

Polarization   

±50° for 4-Port or ±95° for 2-Port  

Speed  

Slewing/Deploying  2°/second 

Peaking  

 0.2°/second 

Drive System 

 

Roto-Lok ® 

Motors    

 

24V DC Variable Speed, Constant Torque 

RF Interface 

Waveguide   

WR 75 Cover Flange at center of azimuth axis 

Coax    

RG59 

Electrical Interface 

25 ft. Cable with Connectors for Controller 

Manual   

 

 

7/16 Hex Socket Wrench on All Axii 

Weight    

 

300 lbs.

 

 

Environmental

 

Wind 

Survival 

   

Deployed  

 

80 

mph 

Stowed  

 

125 

mph 

 

Operational  

Tracking 

 

 

45 mph gusting to 60 mph at 60º F 

Temperature  

 

Operational 

 

 

-20°F to 125°F 

 

Survival 

 

 

-40°F to 140°F 

 

Summary of Contents for 1.8M MVSAT













Reviews: