background image

2

4

safety preCautions

please familiarize yourself with the following information to prevent

damage to your compressor unit and injury to the operator.

Cautions

The air compressor and motor will get hot while in 

operation. Never touch the discharge tubing, motor 

or compressor pump while in operation. The

compressor operates automatically while the power is connected and 

turned on.

WARNING

CAUTION

air reCeiVer

Over pressurizing the air receiver could cause personal injury or material 

damage. To protect from over pressurizing, a factory pre-set safety valve 

is installed.

Any replacement parts should be purchased with the same specifica

-

tions as the original equipment. Please contact the authorized dealer for 

replacement parts or specifications.

neVer weld, drill or Change

the air reCeiVer in any way

safety ValVe

This valve is factory installed to prevent over pressurizing of the air 

receiver. It is factory set at a specific limit for your particular model, and 

should never be tampered with.

do not remoVe,

maKe adJustments to

or substitute this ValVe!

adjustment by user will automatically void the warranty.

Compressed air from the unit may contain hazard-

ous fumes. Air produced by this compressor is not 

suitable for breathing purposes. Always use a res-

pirator when spraying paint or chemicals, or when sandblasting. Always 

wear safety glasses or goggles when using compressed air.
It is not practical or possible to warn you about all the hazards associated 

with operating or maintaining this equipment. You must use your own 

good judgment.

Summary of Contents for PA-C5060

















Reviews: