7) If you intend to use the grass trimmer
function, you have to attach the trimming
guard additionally. Remove the screws and
washers from the outer edge on the guard,
attach the trimming guard and fix it with the
screws and washers.(Fig.5)
NOTE: Local regulations might restrict
the size of the cutting guard so that it
might be necessary to use the bigger
trimming guard for cutting too. Ask
your local authorities.
4
Installing cutting blade
1) Make sure that the cutting guard has
been attached properly and the screws
have been removed from the outer edge.
2) Put the backing flange on the spindle.
3) Fit the cutting blade on the spindle. The
direction of rotation indicated on the guard
must match the one on the cutting blade.
Ensure that the cutting blade sits firmly on
the extruded ring on the backing flange.
4) Put the locking flange on the blade. The
pins must engage in the hole on the
backing flange.
5) Secure the blade with the nut removed
earlier and insert the pin.(Fig.6)
5
Installing spool assembly
1) Make sure that the trimming guard has
been attached properly.
2) Put the backing flange on the spindle
then screw the trimming spool onto
it.(Fig.7)
6
Mixing and filling fuel
WARNING! This petrol brush
cutter is not supplied with fuel in the
engine! Before operating this petrol
brush cutter it is essential to fill in fuel!
WARNING! Not to use biofuels
to operate this petrol brusher cutter.
Ensure that there are no open flames
around the petrol brush cutter! Do not
smoke while filling in fuel and oil!
1) This petrol brush cutter is equipped with
a 2-stroke engine.
2) Mix a regular-grade unleaded petrol and
a quality motor oil for air cooled 2 stroke
engines.
3) Use an anti-oxidant added quality oil
expressly labelled for air-cooled 2 stroke
engine use (JASO FC GRADE OIL or ISO
EGC GRADE).
4) Do not use BIA or TWC (2 stroke
water-cooling type) mixed oil.
5) The recommended mixing ratio for
petrol:oil is 40:1.
6) Place the petrol brush cutter on a stable
and level surface. We recommend laying
an inflammable sheet under the unit.
7) Mix and store fuel only in an approved
petrol container.(Fig.8)
8) Unscrew and remove the fuel tank cap
(17).(Fig.9)
9) Add proper fuel. Do not overfill. Leave
approximately 5mm of space to the lower
edge for fuel expansion.(Fig.10)
10) Use proper a funnel with filter to avoid
that debris can enter the tank and avoid
splitting and overfilling the tank.
11) Wipe up spilled fuel with a soft cloth
and refit the fuel tank cap.
12) Always dispose fuel, used oil and
objects soiled with those according to local
regulations.
Summary of Contents for 8302769
