GB
15
6.4. Tool removal (Fig. 5)
Pull back and hold the locking sleeve (2) and remove
the tool.
7. Starting up
Important.
To prevent all danger, the machine must only be
held using the two handles (5 / 6).
Otherwise there
may be a risk of suffering an electric shock if you drill
into cables.
7.1 ON/OFF switch (Fig. 6/Item 4)
n
First fit a suitable drill bit into the tool (see 6.3).
n
Connect the mains plug to a suitable socket.
n
Position the drill in the position you wish to drill.
To switch on:
Press the ON/OFF switch (4)
Continuous operation:
Secure the ON/OFF switch (4) with the locking
button (8).
Important. It may only be locked if the drill is set to
rotate clockwise.
To switch off:
Press the ON/OFF switch (4) briefly.
7.2 Adjusting the speed (Fig. 6/Item 4)
n
You can infinitely vary the speed whilst using the
tool.
n
Select the speed by applying a greater or lesser
pressure to the ON/OFF switch (4).
n
Select the correct speed: The most suitable
speed depends on the workpiece, the type of use
and the drill bit used.
n
Low pressure on the ON/OFF switch (4): Lower
speed
n
Greater pressure on the ON/OFF switch (4):
Higher speed
Tip:
Start drilling holes at low speed. Then increase
the speed in stages.
Benefits:
n
The drill bit is easier to control when starting the
hole and will not slide away.
n
You avoid drilling messy holes (for example in
tiles).
7.3 Preselecting the speed (Fig. 6/Item 10)
n
The speed setting ring (10) enables you to define
the maximum speed. The ON/OFF switch (4) can
only be pressed to the defined maximum speed
setting.
n
Set the speed using the setting ring (10) on the
ON/OFF switch (4).
n
Do not attempt to make this setting whilst the drill
is in use.
7.4 Clockwise/Counter-clockwise switch
(Fig. 6/Item 9)
n
Change switch position only when the drill is
at a standstill!
n
Switch the direction of the hammer drill using the
clockwise/counter-clockwise switch (9):
Direction Switch
position
Clockwise (forwards and drill) Pushed in to the right
Counter-clockwise (reverse)
Pushed in to the left
7.5 Drill / Hammer drill / Chisel selector switch
(Fig. 7)
n
For drilling, move the selector switch (3) to
position (A).
n
For hammer drilling, move the selector switch (3)
to position (B).
n
For chiseling work, move the selector switch (3) to
position (C).
Important.
Only low pressure is required for hammer drilling.
Excessive pressure will exert an unnecessary force
on the motor. Check the drill bits at regular intervals.
Sharpen or replace blunt drill bits.
8. Replacing the power cable
If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
9. Cleaning, maintenance and
ordering of spare parts
Always pull out the mains power plug before starting
any cleaning work.
9.1 Cleaning
n
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
n
We recommend that you clean the device
Anleitung_E_BH_750_SPK7__ 03.05.12 08:50 Seite 15
Summary of Contents for E-BH 750
Page 3: ...3 1 2 1 2 3 10 6 7 3 6 5 7 4 8 9 6 Anleitung_E_BH_750_SPK7__ 03 05 12 08 50 Seite 3...
Page 4: ...4 4 6 7 2 5 2 9 C B 10 4 8 3 A Anleitung_E_BH_750_SPK7__ 03 05 12 08 50 Seite 4...
Page 65: ...65 Anleitung_E_BH_750_SPK7__ 03 05 12 08 51 Seite 65...
Page 66: ...66 Anleitung_E_BH_750_SPK7__ 03 05 12 08 51 Seite 66...
