background image

EN

116

EN

117

Safety Instructions

GENERAL POWER TOOL SAFETY WARNINGS

WARNING Read all safety warnings, 

instructions, illustrations and speci-

fications provided with this power tool.

Failure to follow the warnings and instructions 

may result in electric shock, fire and/or seri-

ous injury.

Save all warnings and instructions for fu-

ture reference.

The term “power tool” in the warnings refers 

to your mains-operated (corded) power tool or 

battery-operated (cordless) power tool.

1  WORK AREA SAFETY

a) 

Keep work area clean and well lit.

 Clut-

tered or dark areas invite accidents.

b) 

Do not operate power tools in explosive 

atmospheres, such as in the presence of 

flammable liquids, gases or dust.

 Power 

tools create sparks which may ignite the 

dust or fumes.

c) 

Keep children and bystanders away 

while operating a power tool.

 Distractions 

can cause you to lose control.

2  ELECTRICAL SAFETY

a) 

Power tool plugs must match the outlet. 

Never modify the plug in any way. Do 

not use any adapter plugs with earthed 

(grounded) power tools.

 Unmodified plugs 

and matching outlets will reduce risk of 

electric shock.

b) 

Avoid body contact with earthed or 

grounded surfaces, such as pipes, ra-

diators, ranges and refrigerators.

 There 

is an increased risk of electric shock if your 

body is earthed or grounded.

c) 

Do not expose power tools to rain or wet 

conditions.

 Water entering a power tool will 

increase the risk of electric shock.

d) 

Do not abuse the cord. Never use the 

cord for carrying, pulling or unplugging 

the power tool. Keep cord away from 

heat, oil, sharp edges or moving parts. 

Damaged or entangled cords increase the 

risk of electric shock.

e) 

When operating a power tool outdoors, 

use an extension cord suitable for out-

door use.

 Use of a cord suitable for outdoor 

use reduces the risk of electric shock.

f) 

If operating a power tool in a damp loca-

tion is unavoidable, use a residual cur-

rent device (RCD) protected supply.

 Use 

of an RCD reduces the risk of electric shock.

3  PERSONAL SAFETY

a) 

Stay alert, watch what you are doing 

and use common sense when operating 

a power tool. Do not use a power tool 

while you are tired or under the influ-

ence of drugs, alcohol or medication.

 

A moment of inattention while operating 

power tools may result in serious personal 

injury.

b) 

Use personal protective equipment. Al-

ways wear eye protection.

 Protective 

equipment such as dust mask, non-skid 

safety shoes, hard hat, or hearing protec-

tion used for appropriate conditions will re-

duce personal injuries.

c) 

Prevent unintentional starting. Ensure 

the switch is in the off-position before 

connecting to power source and/or bat-

tery pack, picking up or carrying the 

tool.

 Carrying power tools with your finger 

on the switch or energising power tools that 

have the switch on invites accidents.

d) 

Remove any adjusting key or wrench be-

fore turning the power tool on.

 A wrench 

or a key left attached to a rotating part of 

the power tool may result in personal injury.

e) 

Do not overreach. Keep proper footing 

and balance at all times.

 This enables 

better control of the power tool in unexpect-

ed situations.

f) 

Dress properly. Do not wear loose cloth-

ing or jewellery. Keep your hair, cloth-

ing and gloves away from moving parts.

 

Loose clothes, jewellery or long hair can be 

caught in moving parts.

g) 

If devices are provided for the connec-

tion of dust extraction and collection fa-

cilities, ensure these are connected and 

properly used.

 Use of dust collection can 

reduce dust-related hazards.

h)

 Do not let familiarity gained from fre-

quent use of tools allow you to become 

complacent and ignore tool safety prin-

ciples. 

A careless action can cause severe 

injury within a fraction of a second.

4  POWER TOOL USE AND CARE

a) 

Do not force the power tool. Use the cor-

rect power tool for your application.

 The 

correct power tool will do the job better and 

safer at the rate for which it was designed.

b) 

Do not use the power tool if the switch 

does not turn it on and off.

 Any power tool 

that cannot be controlled with the switch is 

dangerous and must be repaired.

c) 

Disconnect the plug from the power 

source and/or the battery pack from 

the power tool , if detachable, before 

making any adjustments, changing ac-

cessories, or storing power tools.

 Such 

preventive safety measures reduce the risk 

of starting the power tool accidentally.

d) 

Store idle power tools out of the reach 

of children and do not allow persons 

unfamiliar with the power tool or these 

instructions to operate the power tool.

 

Power tools are dangerous in the hands of 

untrained users.

e) 

Maintain power tools and accessories. 

Check for misalignment or binding of 

moving parts, breakage of parts and 

any other condition that may affect the 

power tool’s operation. If damaged, have 

the power tool repaired before use. 

Many 

accidents are caused by poorly maintained 

power tools.

f) 

Keep cutting tools sharp and clean.

 

Properly maintained cutting tools with sharp 

cutting edges are less likely to bind and are 

easier to control.

g) 

Use the power tool, accessories and 

tool bits etc. in accordance with these 

instructions, taking into account the 

working conditions and the work to be 

performed.

 Use of the power tool for op-

erations different from those intended could 

result in a hazardous situation.

h) 

Keep handles and grasping surfaces dry, 

clean and free from oil and grease. 

Slip-

pery handles and grasping surfaces do not 

allow for safe handling and control of the 

tool in unexpected situations.

5 SERVICE

a) 

Have your power tool serviced by a qual-

ified repair person using only identical 

replacement parts.

 This will ensure that 

the safety of the power tool is maintained.

ADDITONAL SAFETY INSTRUCTIONS FOR 

ANGLE GRINDERS

a) 

This power tool is intended to function 

as a grinder or cutoff tool. Read all safety 

warnings, instructions, illustrations and 

specifications provided with this power 

tool. 

Failure to follow all instructions listed 

below may result in electric shock, fire and/

or serious injury.

b) 

Operations such as sanding, wire brush-

ing or polishing are not recommended to 

be performed with this power tool.

 Op-

erations for which the power tool was not 

designed may create a hazard and cause 

personal injury.

c) 

Do not use accessories which are not 

specifically designed and recommended 

by the tool manufacturer.

 Just because 

the accessory can be attached to your pow-

er tool, it does not assure safe operation.

d) 

The rated speed of the accessory must 

be at least equal to the maximum speed 

marked on the power tool.

 Accessories 

running faster than their rated speed can 

break and fly apart.

e) 

The outside diameter and the thick-

ness of your accessory must be within 

the capacity rating of your power tool.

 

Incorrectly sized accessories cannot be ad-

equately guarded or controlled.

f) 

The arbour size of wheels, flanges, back-

ing pads or any other accessory must 

properly fit the spindle of the power tool.

 

Accessories with arbour holes that do 

not match the mounting hardware of 

Summary of Contents for PE-125WS


































































Reviews: