72
GB
GB
balance at all times. Proper footing and balance
enables better control of the tool in unexpected
situations.
k.
Do not use on a ladder or unstable support.
Stable footing on a solid surface enables better
control of the tool in unexpected situations.
4. TOOL USE AND CARE
a.
Do not exceed the pressure rating of any
component in the system.
b.
Protect material lines and air lines from damage
or puncture.
Keep hose and power cord away from
sharp objects, chemical spills, oil, solvents,
and wet floors.
c.
Check hoses for weak or worn condition before
each use, making certain all connections are
secure.
Do not use if defect is found.
d.
Purchase a new hose or notify an authorized
service center for examination or repair.
e.
Release all pressures within the system slowly.
Dust and debris may be harmful.
f.
Store idle tools out of the reach of children and
other untrained persons.
Tools are dangerous in
the hands of untrained users.
g.
Maintain tools with care.
Follow maintenance
instructions. Properly maintained tools are easier
to control.
h.
Check for misalignment or binding of moving
parts, breakage of parts, and any other condition
that may affect the operation of the tool.
If damaged,
have the tool serviced before using.
i. Many accidents are caused by poorly maintained tools.
j.
Never point any tool toward yourself or others.
k.
Keep the exterior of the air compressor dry, clean,
and free from oil and grease.
Always use a
clean cloth when cleaning. Never use brake fluids,
gasoline, petroleum-based products, or any strong
solvents to clean the unit. Following this rule will
reduce the risk of deterioration of the enclosure plastic.
5.
SERVICE
a.
Tool service must be performed only by qualified
repair personnel.
Service or maintenance
performed by unqualified personnel may result in a
risk of injury.
b.
Disconnect power supply, open drain valve to
decompress tank and allow water to drain, and
allow air compressor to become cool to the touch
before servicing.
Turn pressure regulator knob
fully counterclockwise after shutting off compressor.
c.
When servicing, use only identical replacement
parts.
Follow instructions in the Maintenance section
of this manual. Use of unauthorized parts or failure to
follow Maintenance instructions may create a risk
of injury.
SPECIAL SAFETY RULES
1.
Know your air compressor.
Read operation manual
carefully. Learn its applications and limitations, as well
as the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
2.
Drain tank of moisture after use each day.
If unit will
not be used for a while, it is best to leave drain valve
open until such time as it is to be used. This will allow
moisture to completely drain out and help prevent
corrosion on the inside of tank.
3.
Risk of fire or explosion.
Do not spray flammable
liquids in a confined area. Spray area must be well
ventilated. Do not smoke while spraying or spray
where spark or flame is present. Keep compressors
as far from the spraying area as possible, at least
4.6 m from the spraying area and all explosive vapors.
4.
Risk of bursting.
Do not adjust regulator to result
in output pressure greater than marked maximum
pressure of attachment and/or the item being inflated.
Never use at pressure greater than 6.8 bar.
5.
Use an air pressure gauge periodically while
inflating an item to check the air pressure.
6.
The machine shall be connected to a circuit
protection device (fuse or circuit breaker).
The
protection device shall be set at 2 A current, and
the user shall do necessary test according to clause
18.2.2 of EN 60204-1:2006 to check if the protection
device is suitable for use.
7.
To reduce the risk of electric shock, do not expose
the machine to rain (water) or dust; store it indoors.
8.
Inspect tank yearly for rust, pin holes, or other
imperfections that could cause it to become
unsafe.
Never weld or drill holes in the air tank.
9.
Make sure the hose is free of obstructions or
snags.
Entangled or snarled hoses can cause loss of
balance or footing and may become damaged.
10.
Use the air compressor only for its intended use.
Do not
alter or modify the unit from the original design or
function.
11.
Always be aware that misuse and improper handling
of this tool can cause injury to yourself and others.
12.
Never step or stand on the work seat.
Following this
rule will reduce the risk of serious personal injury.
