background image

24

Note

The Model 1080ARC communicates in a closed data circuit with 

another Model 1080ARC or other compatible modem.  Dial-up 
analog circuits, such as those used with a standard Hayes-type 
modem, are 

not acceptable

.  For further information about 

acceptable wire grades, please refer to the diagrams in 
Appendix B on page 34.

Point-to-Point Twisted Pair Connection

The 6-position RJ-11 and 8-position RJ-45 jack options for the Model 
1080ARC are prewired for a standard TELCO wiring environment.  Con-
nection of a 2-wire or 4-wire twisted pair circuit between two or more 
Model 1080ARCs requires a crossover cable as shown in Table 27, 
Table 28, Table 29, Table 30 and Figure 8.

Connection to ground is optional
Standard color codes yours may be different

The Model 1080ARC is not sensitive to polarity

Table 27: 

RJ-11/4-Wire

SIGNAL

PIN#

COLOR

COLOR

PIN#

SIGNAL

GND†

1

Blue‡

White

6

GND

RCV-

2

Yellow

Red

4

XMT-

XMT+

3

Green

Black

5

RCV+

XMT-

4

Red

Yellow

2

RCV-

RCV+

5

Black

Green

3

XMT+

GND

6

White

Blue

1

GND

Table 28: 

RJ-45/4-Wire

SIGNAL

PIN#

COLOR

COLOR

PIN#

SIGNAL

GND†

2

Orange‡

Brown

7

GND

RCV-

3

Black

Green

5

XMT-

XMT+

4

Red

Yellow

6

RCV+

XMT-

5

Green

Black

3

RCV-

RCV+

6

Yellow

Red

4

XMT+

GND

7

Brown

Orange

2

GND

Summary of Contents for 1080ARC









































Reviews: