background image

A

APPPPEEN

ND

DIIX

 

C

C

MODEL 2703RC-A-A INTERFACE STANDARDS

X.21 Interface

DB-15 Female Connector

DB15 Female

Pin

Signal

Source

1

Frame Ground

-

2

Transmit (a)

DTE

3

Control (a)

DTE

4

Receive (a)

DCE

5

Indication (a)

DCE

6

Signal Timing (a)

DCE

7

-

-

8

Signal Ground

-

9

Transmit (b)

DTE

10

Control (b)

DTE

11

Receive (b)

DCE

12

Indication (b)

DCE

13

System Clock (b)

DCE

14

-

-

15

-

-

21

A

APPPPEEN

ND

DIIX

 

B

B

MODEL 2703RC-A FACTORY REPLACEMENT PARTS

The Patton Model 2703RC-A rack system features interchangeable

rear cards, power cords/fuses for international various operating envi-
ronments and other user-replaceable parts.  Model numbers, descrip-
tions and prices for these parts are listed below:

Patton Model #

Description

1000RPEM..........................120/240V Rear Power Entry Module
1000RPSM..........................120/240V Front Power Supply Module
1000RPEM-DC ...................DC Rear Power Entry Module
1000RPSM-48A ..................48V Front Power Supply Module
1000RPEM-V ......................120/240V CE Compliant Rear Power 

Entry Module

1000RPSM-V ......................120/240V CE Compliant Front Power 

Supply Module

1180RC DB  ........................V.35 Interface Driver Board
IM1RC/B..............................EIA-530 Interface Driver Board
IM1RC/D ............................EIA-530 Interface Driver Board

1000RCM703120 ................EIA-530/RJ45 120 Ohm Rear Card
1000RCM70375 ..................X.21/Dual Coaxial 75 Ohm Rear Card

0805US ...............................American Power Cord
0805EUR.............................European Power Cord CEE 7
0805UK ...............................United Kingdom Power Cord
0805AUS.............................Australia/New Zealand Power Cord
0805DEN.............................Denmark Power Cord
0805FR ...............................France/Belgium Power Cord
0805IN.................................India Power Cord
0805IS.................................Israel Power Cord
0805JAP..............................Japan Power Cord
0805SW ..............................Switzerland Power Cord

0516FPB1 ...........................Single Width Blank Front Panel
0516FPB4 ...........................4-Wide Blank Front Panel
0516RPB1...........................Single Width Blank Rear Panel
0516RPB4...........................4-Wide Blank Rear Panel

056S1..................................Set of 16 #4 pan head screws/washers

10-25M/15F-1......................Cable, 6ft, DB-25 male to DB-15 

female

10-25M/35F-1......................Cable, 6ft, DB-25 male to M/34 female
10-25M/35M-1.....................Cable, 6ft, DB-25 male to M/34 male

20

Summary of Contents for 2703RC-A













Reviews: