background image

Switches S2-1 and S2-2:  Data Rate

Switches S2-1 and S2-2 are set in combination to determine the

synchronous data rate for the Model 1075.

S2-1

S2-2

Setting

Off

On

32 kbps

On

Off

56 kbps

On

On

64 kbps

Switches S2-3 and S2-4:  System Clock Mode

The setting for switches S2-3 and S2-4 determines the transmitter

clocking mode for the Model 1075.

S2-3

S2-4

Clock Mode

Description

On

On

Internal System 

clock 

generated internally

On

Off

External (DTE)

System clock derived
from terminal interface

Off

On

Receive Recover

System clock derived
from the received line
signal.

Switch S2-5:  Carrier Control

S2-5

Carrier

Description

Off

Always On

Transmitter is always ON

On

Follows terminal 

Transmitter controlled by “Control” 
signal from X.21DTE (or by 
“Indication” signal from X.21 DCE) 

Switches S2-6 and S2-7:  Not Assigned

Switch S2-8:  Front Panel Switch Enable/Disable

Switch S2-8 determines whether the front panel switches may be

used to perform diagnostic functions.

S2-8

Activation

Description

On

Enabled

Front panel switches may be used 
to activate/terminate diagnostics.

Off

Disabled

Front panel switches will have no 
effect on operation of the unit.

6

3.1.1  Configuration Switch Set “S1”

The switches on Switch S1 set V.54 Test Functions.   Default

settings and detailed descriptions for each switch are shown below. 

Switches S1-1 through S1-7:  Not Assigned

Switch S1-8:  V.54 Test Functions

Switch S1-8 enables or disables the Model 1075 V.54 loopback

test modes. 

S1-8

Activation

Description

Off

Enabled

V.54 test functions enabled

On

Disabled

V.54 test functions disabled

3.1.2

Configuration Switch Set “S2”

The switches on Switch S2 set data rates, clock source, carrier

control and front panel switch operation.  Default settings and detailed
descriptions for each switch are shown below.  

S1 SUMMARY TABLE

Position

Function

Factory Default

S1-1 thru S1-7

Not Assigned

Off

S1-8

V.54 Test Functions

Off

Enabled

S2 SUMMARY TABLE

Position

Function

Factory Default

S2-1

Data Rate

On

S2-2

Data Rate

Off

S2-3

Clock Mode

On

S2-4

Clock Mode

On

S2-5

Carrier Control

Off

Forced On

S2-6

Not Assigned

Off

S2-7

Not Assigned

Off

S2-8

Front Panel Switches

On

Enabled

56 kbps

}

5

Internal

}

Summary of Contents for KiloModem II 1075

























Reviews: