background image

PAGE 5

Presenting a valid user token to the unit will cause the LED to briefly flash Green and the door will unlock.  

The presentation of a barred or unknown user token is indicted by a Red LED display.

The external handle is only engaged once access has been granted.  The inside handle is always engaged.

Normal Operation - LED Indications

Software configuration

Reader

: Local settings for the reader.

Output

: Configures the lock for timed release or toggle mode.

Alarm

: Enables/Disables the door alarm functions.   

 

  

  (requires contact switch)

Events

: Shows the events for this control unit only.

Access Rights

: Lists users who have access through this door.

Door name

: Name the Door.

Door open time

: Set the door open time.

Unlock the Door during

: Holds the door unlocked during this 

timezone. - Set to  'At No Time'  for normal user operation.

Red flash
Red and Green flash together

A valid user card has been presented and the handle is engaged
An invalid user card has been presented - No access granted

LED indications

Green flash

The unit is configuring - Please wait.

The access control unit connects to the Net2 software running on the PC using Paxton Net2Air proprietary 

wireless technology. A Net2Air bridge enables communication from the Net2 software to the Paxton wireless 

products.

Radio signals do not always behave as you might expect.  For example, a cell phone that displays a full signal on 

one part of the site will lose signal completely only a few feet away. These problems can be addressed by using 

the Net2 site surveyor kit  (690-200-US)

See also:  

X

AN1095 - Net2 nano - How does it work? <

 

http://paxton.info/974

 >

X

               AN1096 - How to plan a Net2 nano installation <

 

http://paxton.info/975

 >

X

               Ins-30096-US  - Net2Air site surveyor <

 

http://paxton.info/1193

 >

Net2Air wireless communication

Radio frequency

The unit is set to channel 11 (2.405 GHz). This product should not be installed within 10 feet of any other radio 

(LAN/Wi-Fi) equipment to reduce the possibility of interference.

Red and Green flash alternately

The unit is not bound to a bridge.

Summary of Contents for Net2 PaxLock








Reviews: