background image

Model Number

1630-06C

STRAIN GAGE LOAD CELL

Revision: D
ECN #: 43825

Performance

ENGLISH

SI 

Measurement Range

250 lb

1112 N

[5]

Sensitivity(± 10 %)

2 mV/V

2 mV/V

[6]

Non-Linearity

≤ 0.05 % FS

≤ 0.05 % FS

Hysteresis

≤ 0.03 % FS

≤ 0.03 % FS

Non-Repeatability

≤ 0.02 %RO

≤ 0.02 %RO

Resonant Frequency

2.2 kHz

2.2 kHz

Creep(in 20 minutes)

≤ 0.08 %

≤ 0.08 %

Environmental

Overload Limit

375 lb

1668 N

Load Limit(Side Force, F

X

 or F

Y

)

25 lb

111.2 N

[3]

Load Limit

(Bending Moment, M

X

 or M

Y

)

50 in-lb

5.6 Nm

[3]

Load Limit

(Axial Torque, M

Z

)

50 in-lb

5.6 Nm

[3]

Temperature Range(Operating)

0 to +200 °F

-18 to +93 °C

Temperature Range

(Compensated)

+70 to +170 °F

+21 to +77 °C

Temperature Effect on Output(Maximum)

± 0.0008 %Reading/°F

± 0.0015 %Reading/°C

[4]

Temperature Effect on Zero Balance(Maximum)

± 0.0015 %FS/°F

± 0.027 %FS/°C

[4]

Electrical

Bridge Resistance

350 Ohm

350 Ohm

[1]

Excitation Voltage(Recommended)

10 VDC

10 VDC

[2]

Insulation Resistance

>5x10

9

 Ohm

>5x10

9

 Ohm

Zero Balance

± 1 % FS

± 1 % FS

Physical

Size (Length x Height x Width)

2.00 in x 2.50 in x 0.625 in

51 mm x 64 mm x 16 mm [7]

Weight

0.23 lb

104 g

Mounting Thread

1/4-28 thread

No Metric Equivalent

Housing Material

Aluminum

Aluminum

Sensing Element

Strain Gage

Strain Gage

Deflection at Full Scale Capacity

0.0025 in

0.05 mm

Electrical Connector

10 ft - Integrated Cable

10 ft - Integrated Cable

Electrical Connection Position

Side

Side

All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change specifications without notice.

NOTES:

[1]Nominal.
[2]Calibrated at 10 VDC, usable 5 to 20 VDC or VAC RMS.
[3]Singularly applied, i.e. no other extraneous loads.
[4]Over compensated operating temperature range.
[5]FS - Full Scale.
[6]RO - Rated Output.
[7]See Outline Drawing 46137 for Complete Dimensions

PCB Load & Torque, Inc.
24350 Indoplex Circle
Farmington Hills, MI 48335
UNITED STATES
Phone: 866-684-7107
Fax: 716-684-0987
E-Mail: ltinfo@pcbloadtorque.com
Web site: 
http://www.pcbloadtorque.com

OPTIONAL VERSIONS

Optional versions have identical specifications and accessories as listed for the standard 

model except where noted below. More than one option may be used.

Entered: AP

Engineer: PE

Sales: JC

Approved: JSD

Spec Number:

Date: 2/16/2015

Date: 2/16/2015

Date: 2/16/2015

Date: 2/16/2015

45996 

Summary of Contents for PCB Load & Torque 1630-03C













Reviews: