PCE Health and Fitness DeBurr-It! 248-3 User Manual Download | Manualshive

Page: 12 / 17

background image

12

Variable Speed Drive

A variable speed drive option will let you increase or decrease the speed of the motor. We always recommend
using our supplied VFD with the correct parameters already setup for safe operation of the sander. NEVER use
a rheostat to control the speed of any single or polyphase AC induction motor. Please consult DeBurr-It!
technical department if you are using a non supplied VFD.

If no FORWARD/REVERSE control operator is supplied, jump the terminals “COM” to the desired direction.

!!IMPORTANT!! – NEVER OVERRIDE DEFAULT DEBURR-IT! PARAMETER SETTINGS WITHOUT CONSULTING
DEBURR-IT! TECHNICAL DEPARTMENT.

All parameters have been throroughly tested and changing any parameters will void any safety or warranty
conditons.

«
...
10
11
12
13
14
...
»

Summary of Contents for DeBurr-It! 248-3


















Reviews:

No comments

Related manuals for DeBurr-It! 248-3

Brand: Scheppach Pages: 88

Brand: Meec tools Pages: 40

Brand: Draper Pages: 16

Workshop AW200BDS

Brand: Axminster Pages: 24

Brand: XTline Pages: 21

Brand: Universal Tool Pages: 2

Brand: Universal Tool Pages: 4

Brand: PowerTec Pages: 16

Brand: Fortuna Pages: 45

Brand: P.I.T. Pages: 20

Brand: Eagle Pages: 8

Brand: Daewoo Pages: 12

Brand: Hammer Pages: 96

Brand: XTline Pages: 14

Brand: Neilsen Pages: 8

Brand: BorMann Pages: 8

Brand: Makita Pages: 8

Brand: Pattfield Ergo Tools Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands