PCE Health and Fitness DeBurr-It! 248-3 User Manual Download | Manualshive

Page: 7 / 17

background image

7

Runout adjustment hardware

To adjust run out loosen all three lockscrews a few turns.

All new belts and re-tensioned belts will always slightly run off the idler wheel. After changing or retensioning,
turn the Belt Runout Adjustment slightly clockwise. Turn on the sander. Adjust the Belt Runout Adjustment
until the belt is centered on the top crowned idler.

!!IMPORTANT!! – DO NOT RUN THE BELT FOR AN EXCESSIVELY LONG TIME WITH IT BIASED EXTREMELY TO
ONE SIDE OR THE OTHER OF ANY OF THE PULLEYS. DAMAGE TO RUNNING COMPONENTS AND/OR FRAME
WILL OCCUR.

While the machine is still on retighten the lockscrews finger tight. The belt is adjusted.

«
...
5
6
7
8
9
...
»

Summary of Contents for DeBurr-It! 248-3


















Reviews:

No comments

Related manuals for DeBurr-It! 248-3

Brand: Sun-Sniper Pages: 2

Sinorix al-deco STD

Brand: Siemens Pages: 32

ProLINE-RoadRunner

Brand: Siemens Pages: 58

Brand: Siemens Pages: 60

Brand: Skil Pages: 160

Brand: CR Clarke Pages: 27

HeavyDuty PM 1212CES Plus

Brand: Sparky Group Pages: 122

Brand: Record Power Pages: 20

Brand: Dremel Pages: 2

Brand: Doosan Pages: 39

Brand: 3M Pages: 7

Brand: Valex Pages: 16

Brand: Fast Mover Pages: 8

Brand: XTline Pages: 14

Brand: Jet Pages: 24

Brand: Jet Pages: 26

Brand: Chicago Electric Pages: 11

Brand: Bosch Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands