background image

Manual 

12 

Batteries 

When the battery level indicator appears in the left corner of the display, the batteries must be replaced. 
  1. Loose the screws (14) of the battery compartment cover (13) on the rear side of the device. 
  2. Remove the batteries and replace them by 6 new AA batteries. Make sure that the polarity is correct 
      when you insert the batteries. 
3. Fix the battery compartment cover by means of the screws (14). 
 
For the disposal of batteries, the 2006/66/EC

 

directive of the European Parliament applies. Due to the 

contained pollutants, batteries must not be disposed of as household waste. They must be given to 
collection points designed for that purpose. 
 
In order to comply with the EU directive 2012/19/EU we take our devices back. We either re-use them or 
give them to a recycling company which disposes of the devices in line with law. 
 
If you have any questions, please contact PCE Instruments. 
 

Contact 

If you have any questions about our range of products or measuring instruments please contact PCE 
Instruments. 

9.1 

PCE Instruments UK 

By post: 

PCE Instruments UK Ltd. 
Unit 11 Southpoint Business Park 
Ensign Way, Southampton 
Hampshire 
 
United Kingdom, SO31 4RF 
 

By phone:

 

02380 987 035 
 

9.2 

PCE Americas 

By post: 

PCE Americas Inc. 
711 Commerce Way 
Suite 8 
Jupiter 
33458 FL 
USA 
 

By phone:

 

561 320 9162 
 
 
 
 
 
 
 
 

 
 

 

 

Summary of Contents for PCE-313A













Reviews: