Model: PIM-U
Powerline Interface Module
Installation Guide and
Owner’s Manual
FUNCTION
The PIM-U Powerline Interface Module - USB is the de facto
interface between a computer and the Universal Powerline
Bus (UPB). The PIM-U connects to the USB port of your
computer with a standard serial cable (provided) and sends
and receives UPB communication packets on the existing
house wiring. The PIM-U can be plugged into any free wall
outlet throughout the home. No additional wiring is required
and no radio frequency signals are used for communication.
DRIVER INSTALLATION
The very first time that the PIM-U is used with a computer it is
very likely that you will need to install two software drivers
that are included on the mini CD. To do this, follow these
steps:
1.
Insert the mini-CD into the CD (or DVD) drive of your
computer.
2.
Connect the USB serial cable (provided) between your
PIM-U and any USB port of your Windows® based
computer.
3.
Windows should discover the PIM-U and bring up the
“Found New Hardware Wizard”.
4.
Select “No, not this time” and press the Next button.
Windows will bring up the wizard dialog for installing
the USB Serial Converter driver.
5.
Select “Install the software automatically…” and press
the Next button. Windows will install the first driver and
bring up the “Finished” dialog.
6.
Press the Finish button. Windows should, once again,
bring up the “Found New Hardware Wizard”
7.
Select “No, not this time” and press the Next button.
Windows will bring up the wizard dialog for installing
the USB Serial Port driver.
8.
Select “Install the software automatically…” and press
the Next button. Windows will install the second driver
and bring up the “Finished” dialog.
9.
Press the Finish button.
10.
Remove the mini-CD from your computer’s CD drive and
store it for future use.
NOTE
: If you have an internet connection available to your
computer, you can choose to allow the “Found New Hardware
Wizard” to download the drivers off of the internet. In this case
you would not need to use the mini-CD.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical products, basic safety precautions should
always be followed, including the following:
1.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
2.
Keep away from water. If the product comes in contact with
water or other liquid, turn off the circuit breaker and unplug
the product immediately.
3.
Never use products that have been dropped or damaged.
4.
Do not use this product outdoors.
5.
Do not use this product for other than its intended purpose.
6.
To avoid any risk of fire, burns, personal injury or electric
shock, install this product out of the reach of small children.
7.
Do not cover this product with any material when in use.
8.
This product uses grounded plugs and sockets to reduce the
risk of electric shock. These plugs and sockets fit only one
way. If they do not fit, consult an electrician.
9.
SAVE THESE INSTRUCTIONS.
INSTALLATION
The Powerline Interface Module is designed for indoor use with
devices that provide a USB serial port. To install the PIM-U
module follow these steps:
1.
Connect the serial cable (provided) between the PIM’s USB
serial connector and any open USB port of the computer.
2.
Plug the PIM-U into any grounded wall outlet. The Status
LED should start blinking and then stay solid blue.
OPERATION
The PIM-U is the perfect interface device for use with PCS’
UPStart Setup Software. UPStart allows you to easily configure
all of your PulseWorx Lighting System devices. The UPStart
User’s Guide (available on the PulseWorx web site:
www.PulseWorx.com) explains how to configure your system
using UPStart software.
The Inventors Of:
19201 Parthenia St. Suite J
Northridge, CA 91324
(Phone) 818-701-9831 (Fax) 818-701-1506
sales@pcslighting.com www.pcslighting.com
