background image

 

   23                                                                       24

 

F1 500mA/250 FUSE

F2 20A/250V FUSE

9V Batte

9V Battery Door

9V Battery Door Screws

Rear cover screws

Rear cover screws

 
Diode Test 

Test current 

Resolution 

Accuracy 

1.0mA typical 

1 mV 

+5% of rdg +15 dgts 

Open circuit voltage: 3.0V dc typical 

 

Audible Continuity 

Audible threshold: Less than35Ω Test current: <1mA dc typical 
 

Maintenance 

 

REPLACING THE BATTERY

 

WARNING

: To avoid electric shock, disconnect the test leads from 

any source of voltage before removing the battery door. 

1.  When the batteries  become exhausted or drop below the operating 

voltage, “   ”  will appear in the left-hand side of the LCD  display. 

The battery should be replaced. 

2.  Follow instructions for installing battery. See the Battery Installation 

section of this manual. 

3.  Dispose of the old battery properly. 

WARNING: 

To avoid electric shock, do not  operate your meter until 

the battery door is in place and fastened securely. 

 

BATTERY INSTALLATION 

WARNING

: To avoid electric shock, disconnect the test leads from 

any source of voltage before removing the battery door. 

1.  Disconnect the test leads from the meter. 

2.  Open the battery door by loosening the screw using a Phillips head 

screwdriver. 

3.  Insert the battery into battery holder, observing the correct polarity. 

4.  Put the battery door back in place. Secure with the two screws. 

WARNING: 

To avoid electric shock, do not  operate the meter until 

the battery door is in place and fastened securely. 

NOTE

: If your meter does not work properly, check the fuses and 

battery to make sure that they are still good and that they are properly 

inserted. 

REPLACING THE FUSES 

WARNING

:  To avoid electric shock, disconnect the test leads  from 

any source of voltage before removing the rear cover (fuse door). 

1. Disconnect the test leads from the meter and any item under test. 

2. Open the fuse door by loosening the screws on the rear cover using 

a Phillips head screwdriver. 

3. Remove the old fuse from its holder by gently pulling it out.   

3.  Install the new fuse into the holder. 

4.  Always use a fuse of the proper size and value (0.5A/250V -

φ

5 x 20 , 

fast blow for the 400mA range, 20A/250V –

φ

6.3 x 32 fast blow for 

the20A range). 

5.  Put the fuse door back in place. Insert the screw and tighten it 

securely. 

WARNING

: To avoid electric shock, do not operate your meter until the 

fuse door is in place and fastened securely.

 

 

 

 

 

Summary of Contents for DM-930















Reviews: