background image

4

ALL ELECTRICAL WORK MUST BE CARRIED OUT BY A
QUALIFIED ELECTRICIAN.

TROUBLE SHOOTING GUIDE:
Fan will not switch on:

- Switch Off the fan.
- Forward/Reverse switch on fan motor not fully engaged in

desired setting.

- Connections not as per installation diagram.
- Fuse blown, Circuit Breaker tripped or there is a power failure.

- Fan will not operate at varying speed control settings.

- Controller connections not as per page 3.

- Ticking, rattles, mechanical noises.

- Ensure all screws and bolts are tight.
- Ensure the mounting assembly is secure.
- Ensure the lower canopy is clear of the motor.
- With hook mount models, ensure the top canopy is clear of

the ceiling by 5 to 10mm to allow for slight movement of the fan.

- Ensure the wires are not tapping against the canopy.

WARNING:

• Do not attemp to stop the blades by hand, even at low speed.
• This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised
to ensure that they do not play with the appliance.

For further technical support contact PDL National Customer
Service Centre:

WARRANTY

The benefits conferred by this warrantly are in addition to all implied
warranties, other rights and remedies in respect of the product which
the consumer has under the Trade Practices Act and similar State
and Territory Laws.
The original purchaser of this PDL ceiling fan, is provided with the
following warranty, subject to the following conditions:
PDL Industries Australia Pty Ltd warrants this product for a period of
3  years  from  the  date  of  purchase  for  all  parts  defective  in
workmanship  or  materials.  All  products  used  in  commercial
applications are limited to a 90 day warranty.
All defective parts will be replaced free of charge.
The following exclusions do not preclude the purchaser from those
statutory rights consumers have under the Trade Practices Act or
similar State and Territory Laws.

WARRANTY CONDITIONS:

1. This warranty is only valid for appliances installed according to

the manufacturers instructions and for indoor use only.

2. This appliance must not be modified or changed in any way

and all electrical connections must be carried out by a
qualified electrician only.

3. Connection must be to the voltage requirements as specified in

the ratings label located on the product.

4. The manufacturer does not accept liability for any direct or

consequential damage, loss or other expense arising from misuse
or incorrect installation and operation of the appliance.

5. Warranty will only be given where proof of purchase is provided,

eg. original invoice.

6. For warranty to be valid only PDL accessories, such as down

rods and light kits, shall be installed with the PDL Thermosafe
Ceiling Sweep Fan.

IMPORTANT
Record this warranty information at the time of purchase but do not
send this information unless you are making a claim or are asked to
do so.
To  obtain  service  under  warranty  you  must  retain  your  original
purchase receipt, service will otherwise be charged at current rates.

Model No.:

Purchase from:

Name:

Address:

              Postcode:

Date of purchase:

Electrical Products

PDL Industries Australia Pty Ltd
Locked Bag 5500, Baulkham Hills Business Centre
Baulkham Hills NSW 2153 Australia
Freephone 1300 735 266, Freefax 1300 735 329
Tel61 29851 2666, Fax: +61 29851 2695
www.pdl.com.au

Summary of Contents for Thermosafe 4HS1200WH

Page 1: ...n complete each step in order from one to eight INCLUDED WITH YOUR FAN A Motor Assembly B 4 x Blades C 3 Speed Fan Controller D Screw Pack E Mounting Bracket F Instruction Sheet Hangsure Bracket or J Hook Bracket PROTECTING THE FAN Do not place the motor directly onto a flat surface The plastic nipple underneath the motor cannot support the weight of the motor and may be easily damaged When workin...

Page 2: ... Screws 2 3 CONNECTION OF THE LIGHT FITTING If you are attaching a light fitting to the fan do so prior to hanging the fan Note that Clipper Light CL and Oyster Light OL may be installed in fans which are constructed for this purpose 1 Unscrew the plastic nipple from the bottom of the motor housing 2 Pull out the light wires from the motor housing for connection with the lamp holder 3 Insert the l...

Page 3: ...iagram Active to Common C and Switched Active terminal 3 Fix controller to wallbox or bracket using screws provided Replace switch surround 3 7 CONNECTIING THE SPEED CONTROLLER WITH A LIGHT SWITCH Requires additional components not supplied with this fan including PDL 681M20 Switch Mechanism 2 Gang Grid Plate Cover 682VH Fan Only Fan with Light CLEANING INSTRUCTIONS To clean the fan wipe over with...

Page 4: ...es Australia Pty Ltd warrants this product for a period of 3 years from the date of purchase for all parts defective in workmanship or materials All products used in commercial applications are limited to a 90 day warranty All defective parts will be replaced free of charge The following exclusions do not preclude the purchaser from those statutory rights consumers have under the Trade Practices A...

Reviews: