FIGURE 7
FIGURE 8
FIGURE 9
FIGURE 10
FIGURE 11
FIGURE 12
FIGURE 13
FIGURE 14
STEP 2 – Assemble the Cross Rail (E) to the recesses in Left Rail (C) and Right Rail (D) using
Barrel Nuts (I), and 5/16” x 3-1/4” Hex Bolts with washers (J).
a. Identify Cross Rail (E), Barrel nuts (I) and 5/16” x 3-1/4” Hex Bolts with washers (J).
b. Refer to Figure 7. Slide the Cross Rail between each of the Rails (C, D) so that it slots into
the recesses. The two holes in the Cross Rail should face inward, toward the Upholstered
Barrel Assembly. The rails may need to be separated slightly to fit the Cross Rail between
them, but be careful they do not disengage the spring-loaded plungers on the insides
of the Upholstered Barrel Assembly. If they do slip out and disengage the spring-loaded
plungers, go back to Step 1-c and reference Figures 5 and 6 to verify correct position.
c.
Refer to Figure 8. Insert one Barrel Nut (I) into each hole located on the Cross Rail
(E) with the slotted end facing the Upholstered Barrel Assembly. Using a Flathead
Screwdriver, rotate the Barrel Nut until the slot is horizontal. Insert one 5/16” x 3-1/4” Hex
Bolt with washer (J) through each rail from the outside until it engages the threads of the
Barrel Nut. Thread the Hex Bolts into the Barrel Nuts, but do not fully tighten at this time.
STEP 3 – Assemble the Ladder (B) to the L-Brackets on Left and Right Rails (C, D) using
1-1/4” Binding Post Screws (male and female) (F, G).
a. Orient the Ladder (B) so that the black, plastic hole plugs near the top are facing outward,
away from the Upholstered Barrel Assembly.
b. Slide the Ladder between the pre-mounted L-Brackets on each Rail so that the holes are
aligned.
c.
Refer to Figure 9. Carefully squeeze approximately one drop of Loctite into the female
Binding Post Screw (G). Use caution with Loctite, it comes out of the tube quickly.
Beginning at the left side of the Ladder, insert one 1-1/4” Binding Post Screw (female)
(G) from the inside of the Ladder through the L-Bracket and Ladder. From the other side,
insert one 1-1/4” Binding Post Screw (male) (F). Using the two 3/16” Allen (Hex) Wrenches
included, thread the male and female Binding Post Screws together, but do not tighten.
Repeat these steps for the remaining two holes in the L-Bracket on Left Rail (C).
d. Move to the three holes in the L-Bracket on Right Rail (D) and repeat the process using
the remaining three Binding Post Screws (F, G). Using the two 3/16” Allen (Hex) Wrenches,
fully tighten the three sets of Binding Post Screws that attach the Ladder to the L-Brackets
on each side.
STEP 4 - Tighten all Fasteners and Insert ¾” Plastic Hole Plugs (K)
a. Using a Socket Wrench with ½” Socket, firmly tighten both 5/16” x 3-1/4” Hex Bolts from
Step 2. Insert one ¾” Plastic Hole Plug (K) into each Rail.
b. Using the two included 3/16” Allen (Hex) Wrenches, verify that all six (6) sets of Binding
Post Screws (F, G) from Step 3 are firmly tightened.
STEP 5 – Test Your Assembled High Ladder Barrel
a. Your High Ladder Barrel should sit flat on the floor.
b. Test the function of the sliding mechanism by unlocking the Lever-Lock on each side
of the Upholstered Barrel. Figures 10 and 11 show the Lever-Lock in two possible
unlocked positions. After placing the two Lever-Locks are in an unlocked position, push
the Upholstered Barrel Assembly back and forth along the rails. The Upholstered Barrel
Assembly should slide smoothly with minimal resistance.
c.
Test the function of the locked position of the Lever-Locks. Refer to Figure 12 and place
the Lever-Lock on each side of the barrel in its locked position. When in this position, the
Upholstered Barrel Assembly should not slide along the rails.
STEP 6 – Install Flat Foot Plate (OPTIONAL accessory item).
Refer to Figure 13. Set the Flat Foot Plate on to the Rails (C, D), upholstered side facing upward.
The wooden cleats on the underside of the Flat Foot Plate slot between the rails and secure it
from moving laterally.
STEP 7 – Install Vertical Foot Plate (OPTIONAL accessory item)
Refer to Figure 14. Locate the metal bracket on the back of the Vertical Foot Plate and slide it
over the bottom cross-brace on Ladder (B).
Copyright 2013 Mad Dogg Athletics, Inc. All rights reserved. Spin
®
, Spinner
®
, Spinning
®
, the Spinning logo, Peak Pilates
®
, Resist-A-Ball
®
and Bodyblade
®
are registered trademarks that are owned or used under exclusive license by Mad
Dogg Athletics, Inc.
North America
2111 Narcissus Court
Venice, CA 90291 USA
310.823.7008
800.925.3674
Mad Dogg Athletics, Inc.
2111 Narcissus Court Venice, CA 90291 USA
800.847.7746 or 310.823.7008
www.maddogg.com
Europe
Industrieweg 20 A, 3144 CH Maassluis
The Netherlands
+31 1059 04508
www.peakpilates.com
The assembly of your High Ladder Barrel is now complete. Please do not hesitate to contact us with any questions at 1-800-925-3674 or info@peakpilates.com
