background image

– 20 –

1     Frame weldment - Black                                          PA103891 
2     Post A - Black                                                         PA103893 
3     Post B - Black                                                         PA103895 
4     (5/16)M8 x 25 x 1.8 Washer (electroplated)           PA150119 
5     M10 (D41 d10.5 X 3L) Wide washer                       PA0306 
6     M5 x 10 x 1 Flat Washer                                         PA25054 
7     M6 Spring Lock Washer                                          PA11090 
8     M5 Spring Lock Washer                                          PA25053 
9     M 8 x 1.25 Nylon Nut                                              PA100086 
10   M6 x 1.0 Nut                                                           PA150334 
11   Male seven lobe T1 knob  M10 x 1.5 x 25L            PA102705 
12   Bridge/Rail                                                               PA103897 
13   Rear leg weldment                                                  PA103898 
14   Front leg weldment                                                 PA103899 
15   Cable suspension spring                                         PA103924 
16   Spring rest                                                              PA103810 
17   M10 x 1.5 x 60L Cap hex bolt                                 PA4291 
18   M10 x 1.5 Nylon Nut                                               PA140267 
19   M10 x 1.5 x 20L Wing screw                                  PA103820 

20   Cable clamp                                                             PA102719 
21   M4 x 0.7 x 10L Cross screw                                   PA0353 
22   Safety pin with chain                                               PA42148 
23   6 inch Wheel assembly                                           PA140381 
24   Overflow plug assembly                                          PA140224 
25   Table assembly                                                        PA103900 
26   Table support screw                                                PA103901 
27   Table support feet arrangement                              PA103902 
28   20D x 10L M5 Rubber stop                                     PA102751 
29   M6 x 1.0 x 25L Hex bolt                                          PA420319 
30   M5 x 0.8 x 25L Hex bolt                                          PA140282 
31   M5 x 0.8 x 35L Hex bolt                                          PA160081 
32   M8 x 1.25 x 25L Hex bolt                                        PA150145 
33   Ruler guide                                                              PA103903 
34   D4 X 45L Hairpin cotter pin (25D shaft)                 PA140229 
35   M5 x 0.8 x 16L Cross screw                                   PA25058 
36   M6 x 18 x 1.8T Very Big Washer                            PA103904 
37   M6 x 1.0 x 16L Hex bolt                                          PA11089

PART NAME                                                         PART NUMBER

PART NAME                                                         PART NUMBER

FRAME ASSEMBLY

Summary of Contents for VX RSPRO VX1048RSPRO

























Reviews: