background image

3

SAFETY

WARNING! 

NEVER 

operate the unit unless the discharge guard and either the deflector assembly or the 

vacuum collector adapter are fastened securely in place.

WARNING!

 

Do not work around the mower deck boot or the blower area until you are certain that the mower 

blades and the blower impeller have stopped rotating.

WARNING!

 

To avoid serious injury, perform maintenance on the vacuum collector; 

ONLY AFTER 

STOPPING THE MOWER’S ENGINE AND WAITING FOR ALL MOVING PARTS TO COME TO A 

COMPLETE STOP. 

Set the parking brake. Always remove the ignition key before beginning maintenance.

WARNING!

 

For your own personal safety,

 ALWAYS 

mow

 ACROSS 

the face of slopes and 

NEVER UP 

and DOWN

 the face.

 NEVER 

attempt to mow excessively steep slopes, and use caution when turning on any slope.

Safety Alert Symbol

 

 

 

 

 

This Safety Alert Symbol means:

 “ATTENTION! BECOME

 

 

 

 

 

ALERT! YOUR SAFETY IS INVOLVED!”

 

 

 

 

 

This symbol is used to call attention to safety precautions that

 

 

 

 

 

should be followed by the operator to avoid accidents. When

 

 

 

 

 

you see this symbol, carefully read the message that follows

 

 

 

 

 

and heed its advice. Failure to comply with safety precautions

 

 

 

 

 

could result in death or serious bodily injury.

Safety Signs

The signal words

 DANGER, WARNING, 

and

 CAUTION 

are used on the equipment safety signs. These words 

are intended to alert the viewer to the existence and the degree of hazard seriousness. 

!

DANGER

!

WARNING

!

CAUTION

!

This signal word indicates a potentially hazardous situation which, if not 
avoided, will result in death or serious injury.

This signal word indicates a potentially hazardous situation which, if not 
avoided, could result in death or serious injury.

It may also be used to alert against unsafe practices.

This signal word indicates a potentially hazardous situation exist which, if 
not avoided, will result in minor or moderate injury.

It may also be used to alert against unsafe practices.

White letters on

 RED

Black letters on

 ORANGE

Black letters on

 YELLOW

Summary of Contents for 48131301





















Reviews: