PEERLESS Mounts PLAV 70-UNL Installation And Assembly Manual Download

Page: 12 / 13

12 of 13

ISSUED: 06-05-06 SHEET #: 202-9142-4 12-06-06

Mounting and Removing Flat Panel Screen

Refer to mount instruction sheet for attachment of adapter bracket to mount.

Hook adapter brackets (BB or CC) onto adapter bracket (AA), then slowly swing screen in as shown. Turn screws
clockwise at least six times to prevent screen from being removed as shown in detail 4. Tighten using allen wrench (DD).

Screen can be adjusted horizontally if desired.

Note: To lock the screen down, tighten screws to adapter bracket as shown in detail 4.

To remove screen from mount, loosen screws, swing screen away from mount, and lift screen off of mount.

BB or CC

DETAIL 4

SCREWS

BB
or
CC

• Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television.

WARNING

Summary of Contents for PLAV 70-UNL














Search results

Summary of Contents for PLAV 70-UNL

Reviews:

Related manuals for PLAV 70-UNL

Brands by name

Popular brands

PEERLESS Mounts PLAV 70-UNL, Installation And Assembly Manual

Search results

Summary of Contents for PLAV 70-UNL

Reviews:

Related manuals for PLAV 70-UNL

Brands by name

Popular brands