PEERLESS Mounts PLAV 70-UNL Installation And Assembly Manual Download

Page: 3 / 13

3 of 13

ISSUED: 06-05-06 SHEET #: 202-9142-4 12-06-06

PLAV 70-UNL

PLAV 70-UNL-S

PLAV 70-UNLP PLAV 70-UNLP-S

DESCRIPTION

QTY. PART #

PART #

A wall plate

201-1040

201-4040

B tilt-roll assembly

201-1042

201-4042

C arm assembly

201-1044

201-4044

D wall support arm axle

201-1041

E vinyl trim

600-1012

F M10 x 1.5 x 15 mm screw bolt

520-9262

G .505 x .75 x .062" nylon washer

540-1074

H tilt adjustment knob

560-0108

carriage bolt 3/8"-16 x 3.25"

520-1315

J 1.525 x 2 x .062" delrin washer

540-1070

K #8-32 x .375" socket head cap screw

520-1210

L plastic finishing cap

590-1123

M holding pin

580-1166

N retainer plug

590-1007

O 5/16 x 3" wood screw

520-1243

P .250 x 1 x .068" washer

540-1063

Q 9/64" allen wrench

560-9728

R cable management clips

590-1166

S cable tie

590-1168

T 36" polyester mesh sleeve

600-1015

U 6 mm allen wrench

560-9716

W anchor

590-1025

Before you start make sure all parts
listed are included with your product.

Wall Mount Parts List

Some parts may appear slightly different than illustrated.

Summary of Contents for PLAV 70-UNL














Search results

Summary of Contents for PLAV 70-UNL

Reviews:

Related manuals for PLAV 70-UNL

Brands by name

Popular brands

PEERLESS Mounts PLAV 70-UNL, Installation And Assembly Manual

Search results

Summary of Contents for PLAV 70-UNL

Reviews:

Related manuals for PLAV 70-UNL

Brands by name

Popular brands