background image

ISSUED: 05-25-05  SHEET #: 055-9247-6 11-08-06

Visit the Peerless Web Site at www.peerlessmounts.com

1 of 7

For customer care call 1-800-729-0307 or 708-865-8870.

 Read instruction sheet before you start installation and assembly.

Maximum UL Load Capacity: 50 lb (27 kg)

IMPORTANT! Be sure not to touch the projector while tightening the set screw on the
ball and socket mount. This may cause the image to be unaligned when you let go.

Applications:

Flush Mount .................................................................................................................................................. page 5

Extension Column ........................................................................................................................................ page 6

Installations:

To Wood Joist Finished Ceilings,
Exposed Wood Joists, or Wood Beam Ceilings ........................................................................................ page 3

To Concrete Ceilings .................................................................................................................................... page 4

IMPORTANT!  Turn to the appropriate page for your ceiling installation.

Installation and Assembly - Vector Pro II

Models:  PJF2-UNV, PJF2-UNV-S,
PJF2 SERIES
Refer to Model No. Guide Sheet

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and

components.

WARNING

R

This product is intended for use with UL
Listed products and must be installed
by a qualified professional installer.

Summary of Contents for Vector Pro II PJF2-UNV Series








Reviews: