background image

Non-clog submersible sewage pump 
Type UW 

 
 
 
 

Instructions 

 

• 

   Installation

 

• 

     Operation

 

• 

Maintenance

 

 
 

Read this entire book 

before attempting to install, operate or repair this 

 

 

 

 

pump. Properly installed, your Peerless Pump 

 

 

 

 

Sewage Pump will give you satisfactory, dependable 
service.  We  urge  that  you  read  carefully  these          
step-by-step  instructions,  to  simplify  any  problems         
of installation, operation or repair. 
Failure to read and comply with installation and 
operating   instructions  will   void   the   responsibility   of 
 
 
 
 
 
 
New equipment manufactured by Seller is warranted to 
be free from defects in material and workmanship under 
normal use and service for a period of one year from 
date of shipment;  Seller’s obligation under this warranty 
being limited to repairing or replacing at its option any 
part found to its satisfaction to be so defective provided 
that such part is, upon request, returned to Seller’s 
factory from which it was shipped, transportation 
prepaid.  This warranty does not cover parts damaged 
by decomposition from chemical action or wear caused 
by abrasive materials, nor does it cover damage 
resulting from misuse, accident, neglect, or from 
improper operation, maintenance, installation, 
modification or adjustment.  This warranty does not 
cover parts repaired outside the Seller’s factory without 
prior written approval.  Seller makes no warranty as to 
starting equipment, electrical apparatus or other material 
not of its manufacture, since the same are usually 
covered by warranties of the respective manufacturers 
thereof. 
 
 
 
 
 
 
                                 

Peerless Pump Company 

                                 

Indianapolis IN, 46207-7026 

 

 
 
 
the manufacturer and may also result in bodily injury as 
well as property damage. 
This book is intended to be a permanent part of your 
installation and should be preserved in a convenient 
location for ready reference.  If these instructions should 
become soiled, obtain a new copy from Peerless. 

 

Include pump model and/or serial number with your 
request.  
 
 
 
 
 

WARRANTY

 
In the event, notwithstanding the terms of this 
agreement, it is determined by a court of competent 
jurisdiction that an express warranty has been given by 
Seller to Purchaser with respect to the head, capacity or 
other like performance characteristics of said equipment, 
Seller’s liability for breach of the same shall be limited to 
accepting return of such equipment F.O.B. plant of 
manufacture, refunding any amount paid theron by 
Purchaser (less depreciation at the rate of 15% per year 
if Purchaser has used the equipment for more than thirty 
(30) days) and canceling any balance still owing on the 
equipment. 
 
 

 
THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY 
OTHER WARRANTIES, EXPRESSED OR IMPLIED, 
AND SELLER SPECIFICALLY DISCLAIMS ANY 
IMPLIED WARRANTY OF MERCHANTABILITY OR 
FITNESS FOR A PARTICULAR PURPOSE. 
 
 
 
 
 
 

  

 

2899213 

  REV 4-79 

 

Summary of Contents for UWLLB3













Reviews: