background image

ISSUED: 09-19-05  SHEET #: 055-9441-5 10-31-08

Visit the Peerless Web Site at www.peerlessmounts.com

2 of 12

For customer care call 1-800-729-0307 or 708-865-8870.

Table of Contents

Parts List .......................................................................................................................................................................... 3

Installation to Extension Columns / Ceiling Plate .............................................................................................................. 4

Installation to Wood Joist Ceilings .................................................................................................................................... 5

Installation to Concrete Ceilings ........................................................................................................................................ 6

Installation to Threaded Rods ............................................................................................................................................ 7

Attaching Adapter Plate to Projector ................................................................................................................................. 8

Projector Alignment ........................................................................................................................................................ 10

Accessories .............................................................................................................................................................. 11, 12

Tools Needed for Assembly

• stud finder ("edge to edge" stud finder is recommended)
• phillips screwdriver
• drill

Note: Read entire instruction sheet before you start installation and assembly.

• 1/4" bit for concrete surface
• 5/32" bit for wood studs
• level

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
call Peerless customer care at 1-800-865-2112.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-

ware and components.

• Never exceed the Maximum Load Capacity. See page 1.

• If mounting to wood ceiling studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.

• This product was designed and intended to be mounted to the following supporting surfaces checked below with the

hardware included in this product as specified in the installation sheet. To mount this product to an alternative support-
ing surface, contact Peerless customer care at 1 800 865-2112.

• This product was designed to be installed on the following ceiling construction only;

CEILING CONSTRUCTION

ADDITIONAL HARDWARE REQUIRED

x

Wood Stud

None

x

Wood Beam

None

x

Solid Concrete

None

Cinder Block

Contact Customer Service

Metal Stud

Contact Customer Service

Brick

Contact Customer Service

Other or unsure?

Contact Customer Service

WARNING

Summary of Contents for PRS-UNV













Reviews: