background image

  ISSUED 08-09-06 SHEET #: 055-9470-1

Visit the Peerless Web Site at www.peerlessmounts.com

2 of 11

For customer care call 1-800-729-0307 or 708-865-8870.

Note:

 Read entire instruction sheet before you start installation and assembly.

Tools Needed for Assembly

stud finder ("edge to edge" stud finder is recommended)

phillips screwdriver

drill with 1/4", 3/8", and 5/32" drill bits

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
call Peerless customer service at 1-800-729-0307.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-

ware and components.

• Never exceed the Maximum Load Capacity of 30 lb (13.6 kg).

• If mounting to wood ceiling joists, make sure that mounting screws are anchored into the center of the joists. Use of

an "edge to edge" stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

WARNING

Accessories

Lightweight Adjustable Suspended Ceiling Kit (CMJ 500)

Lightweight Suspended Ceiling Kit (CMJ 455)

Accessory Pack for CMJ 455 (ACC 455)

Lightweight Cathedral Ceiling Plate (ACC 912)

Unistrut or Structural Ceiling Plates (CMJ 300, CMJ 310)

Anti-Vibration Ceiling Plates (ACC 845)

I-Beam Clamps (ACC 558, ACC 559)

Truss Ceiling Adapter (ACC 557)

Unistrut Adapter (ACC 550)

Escutcheon Ring (ACC 640)

Round Ceiling Plate (ACC 570)

Cord Wrap (ACC 852, ACC 852W, ACC 852S)

3/4" Pipe Reducer (ACC 913)

Fixed Length 1 1/2" Extension Columns
(EXT models)

Adjustable Length 1 1/2" Extension Columns
(ADJ models)

Extension Column Stabilizer Kit (ACC 050)

Extension Column Connector (ACC 109)

1/2" Threaded Rod (ACC 820)

Threaded Rod Adapter (ACC 810)

Installations:

To Wood Joist Finished Ceilings,
Exposed Wood Joists, or Wood Beam Ceilings ........................................................................................ page 5

To Concrete Ceilings .................................................................................................................................... page 6

To Threaded Rod, or Extension Columns .................................................................................................. page 7

Projector Alignment:

Adjusting Roll Pitch and Yaw ................................................................................................................... page 11

IMPORTANT!  Turn to the appropriate page for your ceiling installation.

Summary of Contents for PSMU-PRS












Reviews: