For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• The toy must be used with caution, as it requires
substantial dexterity in order to avoid falls or
collisions which could cause injuries to the user or
third parties.
• Before starting, check that there are no people or
objects obstructing the vehicle’s path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
ATTENTION!
The item is equipped with a brake
system which needs to be appropriately illustrated to
the child by an adult.
2nd GEAR (if present)
Initially, use in 1st gear is recommended. Before
enabling 2nd gear, check that the child has learned to
use the handlebars/steering wheel, 1st gear and the
brake correctly, and has become familiar with the
vehicle.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
switch will immediately disconnect the power. The
power supply will be restored after a few seconds.
• If the vehicle is overloaded on steep slopes, the
overload cut-out will immediately disconnect the
power. If this happens,
REMOVE THE FOOT FROM THE
ACCELERATOR
. The electrical brake will be
activated, slowing down the descent of the vehicle.
• Only for 12 and 24 Volt vehicles: in first gear the
vehicle has a differential effect like a real motor
vehicle; on smooth terrain and with just one child
on board, the two wheels can turn at different
speeds and they can slip and slow down.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
THE VEHICLE DOES NOT WORK?
• Check that there are no disconnected cables under
the accelerator plate.
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.
PROBLEMS?
RULES FOR SAFE DRIVING
PEG PEREGO offers an after-sales assistance
service, directly or through a network of
authorized assistance centres, for any repairs or
replacements and the sale of original spare parts.
To contact a service center, visit our website:
http://global.pegperego.com/toys-site/support/
The item’s serial number must always be quoted.
See the page on spare parts to find out how to
identify the serial number.
Peg Perego always strive to best satisfy their
customers' needs. Knowing the opinions of our
customers is therefore very important and
valuable to us. We would be very grateful if, once
you have used the product, you would fill out the
CONSUMER SATISFACTION QUESTIONNAIRE
which you can find on the internet at:
www.pegperego.com
, making any observations
or suggestions you might have.
ASSISTANCE SERVICE
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
ASSEMBLY
1 • Snap together the 2 halves of the bronze
simulated engine.
2 • Insert the simulated engine into the vehicle, as
shown in the figure.
3 • Press on the points shown by the arrows on the
toy engine (on each side), to fasten the engine.
4 • Lift both rear shock absorbers, and line them up
with the openings in the chassis.
5 • To fasten the shock absorbers to the chassis,
insert the pins into the top holes on the shocks,
with the tabs turned vertically (see detail).
6 • Finish fastening the shock absorbers by placing
the plastic tool on the pins and hammering the
pins all the way in.
7 • Snap the nut cap into place, and repeat the
operation on the other three wheels.
8 • Attach seat by inserting black tabs on seat into
slots on body. Then rotate down into place.
9 • Attach red seat lock by inserting through seat
and into body.
10 • Attach black radiator piece by first inserting tabs
into corresponding rectangular slots (a). Then
press firmly on the upper tabs (b) so that they
fully engage into their slots.
11 • Position front rack onto supports as shown in
figure and secure with 4 screws provided.
12 • Apply radiator decal.
13 • Insert the two brackets into the openings on the
radiator, as shown in the figure.
14 • Attach charcoal front grill to front rack by lining
up connection points and snapping into place.
15 • Attach the silver front brush guard by lining up
connection points and snapping into place.
16 • Fasten the grill with the 2 screws.
17 • Attach the two chrome decals to the headlight
positions on the grill.
18 • Snap the two headlights onto the grill.
19 • Attach the chrome decal to the chassis, as shown
in the figure.
20 • Snap the taillight into place by inserting it from
the top.
21 • To attach folding extra seatback, insert one of
the posts into the rear rack.
22 • Position seatback with handle down and slide peg
into hole on post.
23 • Slide second post onto peg on seatback (a) and
then press post down into position (b).
24 • Folding extra seatback with posts in place.
25 • While holding seatback and posts in position,
fasten posts using screws provided.
26 • Connect rear rail to rear rack by inserting tabs
on rail into slots on rack, rotating into place and
fastening using screws provided.
27• Position rear rack onto supports as shown in
figure and secure with 4 screws provided.
28 • Snap the toy gas cap into place on the vehicle.
29 • Assemble handlebar/headlight unit as shown in
figure.
30 • Apply chrome decal as shown in figure.
31 • Attach clear headlight lens.
32 • Attach black speedometer piece to headlight
housing. Then apply speedometer decal.
33 • Attach clear speedometer lens and fasten using
small screw provided.
34 • Slip the two handguards onto the handlebars,
lining up the holes in the handguards with the
holes in the handlebars.
35 • Fasten the hand guards with the two screws.
36 • Slip the handgrips onto the handlebars as shown.
37 • Snap handlebar into place on the vehicle.
38 • Turn the seat lock to the “unlock” position
shown in the diagram, and lift the seat. NOTE:
Seat has a lock and unlock position.
39 • Remove the battery retainer by squeezing in on
the sides and sliding it free of the slot in the
body.
40 • Slide the battery into the battery compartment.
41 • Connect wiring system of the vehicle (plug
A
) to
the battery (plug
B
).
42 • Replace the battery retainer.
43 • Close the seat. ATTENTION: Always make sure
that the seat is closed and locked after carrying
out any operations inside it.
ASSEMBLY INSTRUCTIONS
FEATURES AND USE OF THE VEHICLE
44 • Exclusive
SmartPedal Technology™
feature
allows for longer run times and more realistic
driving. In “LOW” setting, when accelerator is
pressed completely down, forward motion at 5,2
km/h is activated. In “HIGH” setting, when pedal
is pressed completely down, forward motion
begins at 5,2 km/h for a few seconds and then
automatically accelerates to 10 km/h. In “HIGH”
setting, when pedal is released halfway, vehicle
automatically “downshifts” to 5,2 km/h. Brake
activates automatically when the child takes his
foot off the accelerator.
45 • ATTENTION: For safety, when the vehicle is first
removed from the packing, it is in the LOW
setting. Peg Perego suggests that the LOW
setting be used until your child has become
familiar with operating the vehicle. To adjust high-
speed lockout, loosen screw.
46 • Then slide safety collar down into HIGH setting
and replace screw.
47 • GEAR SHIFT LEVER: The vehicle has two
directions. To use REVERSE (
R
), pull back and
hold the gearshift lever. NOTE: For safety,
gearshift must be held back in the reverse
position.
48 • Exclusive
Red Line Nitrile Traction™
: The
wheels on this vehicle feature an extra deep
tread AND a special rubber traction band for
incredible traction on most surfaces and a quiet
ride.
49 • To raise and lower the folding extra seatback,
pull up on the handle on the back of the
seatback.
REPLACING THE BATTERY
PLEASE NOTE: THE PICTURES OF THE BATTERIES
ARE FOR ILLUSTRATIVE PURPOSES ONLY. YOUR
BATTERY MAY BE DIFFERENT FROM THE MODEL
SHOWN. THIS DOES NOT AFFECT THE
REPLACEMENT AND CHARGING PROCEDURES
DESCRIBED.
50 • First unlock and lift the seat.
51 • Disconnect the electrical system plug (
A
) from
the battery plug (
B
) by pressing on the sides of
the plugs and pulling apart.
52 • Remove the battery retainer by squeezing in on
the sides and sliding it free of the slot in the
body.
53 • Remove old battery and replace with new
battery.
54 • Replace the battery retainer.
55 • Close the seat. ATTENTION: Always make sure
that the seat is closed and locked after carrying
out any operations inside it.
CHARGING THE BATTERY
WARNING: BATTERY CHARGING AND ANY
OTHER WORK ON THE ELECTRICAL SYSTEM
MUST BE CARRIED OUT BY ADULTS.
THE BATTERY CAN ALSO BE CHARGED
WITHOUT REMOVING IT FROM THE TOY.
56 • First unlock and lift the seat.
57 • Disconnect the electrical system plug (
A
) from
the battery plug (
B
) by pressing on the sides of
the plugs and pulling apart.
58 • Plug the battery charger into a household
electrical outlet. Connect battery plug (
B
) to
charger plug
C
. NOTE: Press firmly until it snaps
into place.
59 • After battery has finished charging (full charge
takes 18-24 hours), disconnect battery charger
from the electrical outlet and then disconnect
the battery plug (
B
) from the charger plug (
C
).
60 • Reconnect electrical system plug (
A
) to battery
plug (
B
). NOTE: Press firmly until it snaps into
place.
61 • Close the seat. ATTENTION: Always make sure
that the seat is closed and locked after carrying
out any operations inside it.
Summary of Contents for IGOD05150
