Pegasus Astro Dual Motor Focus Controller Manual Download | Manualshive

Page: 9 / 16

background image

9 Pegasus Astro – Copyright 2016

Standalone DMFC Application

Standalone application does not require ASCOM drivers and it can configure and operate
the Dual Motor Focus Controller.

In order to connect from the supplied software to the controller, you need to first configure
the serial port

•

Click on “Settings” icon

The following window will appear

«
...
7
8
9
10
11
...
»

Summary of Contents for Dual Motor Focus Controller

















Reviews:

No comments

Related manuals for Dual Motor Focus Controller

Brand: Microchip Technology Pages: 37

Brand: CAME Pages: 12

Brand: CAME Pages: 16

Brand: Ultrak Pages: 41

Brand: Zander Aachen Pages: 10

Brand: BADODOSECURITY Pages: 8

Brand: Daikin Pages: 2

Brand: Daikin Pages: 12

Brand: Daikin Pages: 12

Brand: Daikin Pages: 46

Brand: Daikin Pages: 21

Brand: Daikin Pages: 20

Brand: Gate Motors Pages: 6

Brand: Lamtec Pages: 136

Brand: vacuubrand Pages: 12

Brand: Vacon Pages: 47

Brand: Vacon Pages: 40

Brand: Valco baby Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands