PELA 498192, Manual

Enter information about the rim

Move the scale to make the inner front edge of the 

handle the inner position of the handle as the figure 

above get value a, put the scale back. Press [a-] or 

[a +] to enter a value.
Input rim width- Get rim width data displayed on 

the rim, or measure the rim width with thickness, 

press [b-] or [b +] to enter b-value.
Input rim diameter- Get rim diameter data 

displayed on the rim, or measure the rim diameter 

using thickness, press [d-] or [d +] to enter the d 

value.
Balancing against normal dynamic balancing 

mode- Input rim data, manually rotate the wheel, 

when the display shows “RUN ---”, remove the hand 

to allow the wheel to rotate. When the display 

shows ”STOP”, the wheel stops and the display 

shows data. Slowly rotate the wheel, when the 

indicator lights of the indicator light are on, place 

the clamp weights equal to the value shown on the 

left display inside at 12 o’clock.
Then slowly rotate the wheel, when the indicator 

lights on the outside position illuminate all the 

light at 12 o’clock on the rim outside. Place clamp 

weights equal to the value shown on the right side 

display. Rotate the wheel by hand again, remove 

the hand when the display is off. When the side 

display is on, the wheel stops and balancing is 

complete.

Static (ST) balancing mode data input 

method and balancing operation

The (ST) position is suitable for rims where only 

weights can be placed in the middle position, e.g. 

motorcycle rims. In normal measurement, measure 

the diameter d-value, press [d-] or [d +] to enter the 

d-value. (A value and b-value can be any value). 

Press the [MODE] button to activate the ST 

indicator light, set static (ST) balancing mode, 

position indication as shown in the following figure.

Input rim data, manually rotating the wheel, when 

the display shows “RUN ---”, move your hand away 

to allow the wheel to rotate. Then the right display 

shows ST and the left display static imbalance, 

see picture below. When the wheel stops rotating, 

slowly rotate the rotating wheel in advance. When 

the internal position indicator lamps and the 

external position indicator lamps are lit at all 

weights equal to the value shown on the left-hand 

side, at 12 o’clock on the center rim. Rotate the 

wheel manually, when the display shows “RUN ---”, 

move the handle to rotate the wheel. Both side 

displays are on and the wheel stops and the 

balancing is complete.

ALU-1 mode data input method and balancing 

operation

Enter rim data, press the 

[MODE] button, position 

indication as below, then enter 

ALU-1 position to balance the 

wheel.
Feed rim data with manually rotatable wheel, when 

the display shows ”RUN ---”, remove your hand to 

allow the wheel to rotate. When the display shows 

”STOP”, the wheel stops and the display shows 

data. Slowly rotate the wheel, when the indicator 

lights on the internal position are lit, at 12 o’clock 

place weights equal to the value shown on the left 

side display. Then slowly turn the rotary 

wheel, when the indication of the external position 

lamp lights up on all indicators at 12 o’clock. Stick 

weights corresponding to the value shown on the 

right side, see picture below. Turn the wheel 

beforehand again, when the display shows ”RUN --”, 

move the hand away to allow the wheel to rotate. 

When both side displays are on, the wheel stops 

and balancing is complete.

ALU-2 mode data entry method and  

balancing operation

Enter rim data, press the [MODE] button, position 

indication as below, then enter the ALU-2 position 

to balance the wheel. Input field data, manually 

rotatable wheel, when the display shows ”RUN ---”, 

remove the hand to allow the wheel to rotate. When 

the display shows ”STOP”, the wheel stops and the 

display shows data. Slowly rotate the wheel, when 

the indicator light in the inlet position lights up.