Pella 808F0105 Installation Instructions Manual Download

Page: 1 / 8

Part Number: 808F0105

REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT.

INSTALLATION INSTRUCTION -

INSTRUCCIONES DE INSTALACION

PELLA

PRECISION FIT AND RENOVATION POCKET

REPLACEMENT DOUBLE-HUNG VENT WINDOW

Always read the Pella® Limited Warranty before purchasing or installing Pella

products. By installing this product, you are acknowledging that this Limited Warranty

is part of the terms of the sale. Failure to comply with all Pella installation and maintenance

instructions may void your Pella product warranty. See Limited Warranty for complete details at

http://warranty.pella.com.

INTERIOR

Flashing tape

Checkrail

YOU WILL NEED TO SUPPLY:

TOOLS REQUIRED:

• Cedar or Impervious shims/spacers (12 to 20)

• Closed cell foam backer rod/sealant backer (12 to 30

ft.)

• Pella

SmartFlash

™

foil backed butyl window

and door flashing tape or equivalent

• High quality exterior grade polyurethane or silicone

sealant (1 tube per window)

• Great Stuff ™ Window and Door Insulating Foam

Sealant by the Dow Chemical Company or equivalent
low pressure polyurethane window and door foam -

DO NOT use high pressure or latex foams.

• Tape measure

• Level

• Hammer

• Utility knife

• Pry bar

• Sealant gun

• Screwdrivers

(#2 Phillips and Flat blade)

• Putty knife

• Wood chisel

• Drill

Installation will require two or more persons for safety reasons.

SEALANT

Important!

The Pella Replacement Window is designed to replace older style double-hung

windows. The original window frame will remain in place and only the existing sash will be

removed. Read these instructions thoroughly before beginning. Failure to install as recommended

will void any warranty, express or implied. For types of installation other than shown, contact your

local Pella representative or

visit

http://www.pella.com.

Summary of Contents for 808F0105









Search results

Summary of Contents for 808F0105

Reviews:

Related manuals for 808F0105

Brands by name

Popular brands

Pella 808F0105, Installation Instructions Manual

Search results

Summary of Contents for 808F0105

Reviews:

Related manuals for 808F0105

Brands by name

Popular brands