Pella 812W0100 Installation Instructions Manual Download

Page: 1 / 11

INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN
FOR CLAD AWNING, CASEMENT &
NON-RECTANGULAR CASEMENT WINDOW
PARA LAS VENTANAS DE MADERA RECUBIERTAS DE ALUMINIO
TIPO BISAGRAS, BATIENTE Y BATIENTE NO-RECTANGULAR

Installation Instructions for Typical Wood Frame Construction.

These instructions were developed and tested for use with typical wood frame wall construction

in a wall system designed to manage water. These instructions are not to be used with any

other construction method. Installation instructions for use with other construction methods,

multiple units or bow and bay windows, may be obtained from Pella Corporation, a local Pella

retailer, or by visiting

http://www.pella.com

. Building designs, construction methods, building

materials, and site conditions unique to your project may require an installation method

different from these instructions and additional care. Determining the appropriate installation

method is the responsibility of you, your architect, or construction professional.

Framing

Corner

Flashing

Tape

Top

Flashing

Tape

Corner

Flashing

Tape

Fin

Corner

Window Top

Nailing Fin

Window Bottom

Side

Flashing

Tape

Side

Flashing

Tape

Sill Flashing Tape #2

Sill Flashing Tape #1

Water Resistive Barrier

Sheathing

Part Number: 812W0100

Always read the Pella

Limited Warranty before purchasing or installing Pella products. By

installing this product, you are acknowledging that this Limited Warranty is part of the terms of the

sale. Failure to comply with all Pella installation and maintenance instructions may void your Pella

product warranty. See Limited Warranty for complete details at

http://warranty.pella.com.

Summary of Contents for 812W0100












Search results

Summary of Contents for 812W0100

Reviews:

Related manuals for 812W0100

Brands by name

Popular brands

Pella 812W0100, Installation Instructions Manual

Search results

Summary of Contents for 812W0100

Reviews:

Related manuals for 812W0100

Brands by name

Popular brands