Pella INSYNCTIVE DESIGNER Series Product Manual Download | Manualshive

Page: 10 / 15

background image

PELLA

®

DESIGNER SERIES

®

BETWEEN-THE-GLASS BLINDS AND SHADES WITH INSYNCTIVE

®

TECHNOLOGY

|

10

WITH HOME AUTOMATION

BRIDGE supports two types of home automation systems:
Professionally Installed and Do-It-Yourself (DIY) Z-Wave. For
a list of compatible home automation systems or syncing
instructions, visit Pella.com/Insynctive.

NOTE:

If you have a Z-Wave home automation system, the

order in which you sync BLINDS or SHADES to BRIDGE is the
order by which they will be included into the Z-Wave network.
Write down the order in which each BLIND or SHADE is synced
to BRIDGE so you can identify and assign a name when it shows
up in your Z-Wave network.

DETAILED INSTRUCTIONS

(continued)

«
...
8
9
10
11
12
...
»

Summary of Contents for INSYNCTIVE DESIGNER Series
















Reviews:

No comments

Related manuals for INSYNCTIVE DESIGNER Series

Brand: VALE BLINDS Pages: 16

Brand: PENTAGON Pages: 12

Brand: GEIGER Pages: 20

Fixscreen 100EVO Solar

Brand: Renson Pages: 28

Brand: PALAGINA Pages: 56

Brand: Marinello TENDE Pages: 2

Brand: Plissees Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands