Pella INSYNCTIVE DESIGNER Series Product Manual Download | Manualshive

Page: 15 / 15

background image

PELLA

®

DESIGNER SERIES

®

BETWEEN-THE-GLASS BLINDS AND SHADES WITH INSYNCTIVE

®

TECHNOLOGY

|

15

FCC COMPLIANCE AND INDUSTRY CANADA

This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a different circuit from the receiver.

• Consult the dealer or an experienced radio/TV contractor for help.

Changes or modifications not expressly approved by Pella Corporation could void the user’s authority to
operate the equipment.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.

Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS. L’opération est
soumise aux deux conditions suivantes: (1) cet appareil ne peut causer d’interférences, et (2) cet
appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais
fonctionnement de l’appareil.

FCC ID: SO7-206B0000
IC: 11009A-206B0000

LIMITED WARRANTY

A two-year limited warranty comes standard with purchase. For complete warranty details,
visit Pella.com/Warranty.

© 2016 Pella Corporation

IDSPG1216

«
...
13
14
15

Summary of Contents for INSYNCTIVE DESIGNER Series
















Reviews:

No comments

Related manuals for INSYNCTIVE DESIGNER Series

Brand: Isotra Pages: 12

Brand: Velux Pages: 52

CHAIN & CORD ROMAN BLINDS

Brand: Betta Pages: 3

Brand: Hard Head Pages: 17

Brand: Swiss Sonnenschutz Pages: 4

Shiori 25 Drum Twin

Brand: TOSO Pages: 6

EasyRise Duette

Brand: LuxaFlex Pages: 24

Brand: LuxaFlex Pages: 33

ZANZARA 4251648823483

Brand: JAROLIFT Pages: 44

Brand: Isotra Pages: 4

Brand: Isotra Pages: 5

Brand: Isotra Pages: 11

Brand: Isotra Pages: 14

Brand: Diaz Pages: 3

Brand: Diaz Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands