Pella INSYNCTIVE DESIGNER Series Product Manual Download

Page: 2 / 15

PELLA

DESIGNER SERIES

BETWEEN-THE-GLASS BLINDS AND SHADES WITH INSYNCTIVE

TECHNOLOGY

TABLE OF CONTENTS

General and Safety Information

Need Help?

Have a Home Automation System?

Warnings

Product Overview

Specifications

Detailed Instructions

Setting Up Pella

Designer Series

Between-the-Glass Blinds or Shades

Programming Positions

Operating Blinds or Shades with Remote

Tilting Blind Slats

Syncing to Pella Bridge

With Home Automation

Additional Instructions

Charging Battery in Blinds or Shades

Care and Maintenance

Replacing Batteries

Adding or Deleting a Remote

“Homing” Blinds or Shades

Resetting to Factory Defaults

Troubleshooting
FCC Compliance and Industry Canada
Limited Warranty
Software License Agreement and Privacy Policy

Summary of Contents for INSYNCTIVE DESIGNER Series
















Search results

Summary of Contents for INSYNCTIVE DESIGNER Series

Reviews:

Related manuals for INSYNCTIVE DESIGNER Series

Brands by name

Popular brands

Pella INSYNCTIVE DESIGNER Series, Product Manual

Search results

Summary of Contents for INSYNCTIVE DESIGNER Series

Reviews:

Related manuals for INSYNCTIVE DESIGNER Series

Brands by name

Popular brands