background image

A. 

Score paint or varnish 

along 

interior sash stops with a sharp 
utility knife. Carefully remove 

INTERIORSASHSTOPSATJAMBSSIDES
ANDHEADTOP USINGPUTTYKNIFE

and prybar. Set aside to reuse.

B. 

Cut the balance cords

 on the 

bottom sash and lift out the sash. 
Allow weights to fall to the bottom 
of the weight pocket.

C. 

Remove the parting stops.

 There 

may be a small wedge of wood at 
the bottom of the upper sash that is 

NEXTTOTHEPARTINGSTOPS4OMAKE

it easier to remove the parting stop, 
use a chisel to knock off the wedge.

D. 

Lower the top sash and cut the 
balance cords

 allowing the balance 

weights to fall into the weight 
pocket. Remove the top sash. Be 

CAREFULNOTTODAMAGETHEEXTERIOR

blind stop.

E.

  Remove the balance cord pulleys. 

Unscrew and remove balance cord 
pulleys. If they cannot be removed 
easily, drive them into the jamb 
using a hammer.

1

 REMOVING EXISTING SASH

Caution: Many windows in older homes are painted with lead-based paint. Removal of old 
windows may disturb this paint. Proper precautions must be taken to minimize exposure to dust 
and debris. Consult state or local authorities for more information. Use appropriate personal 
protective equipment.

A. 

Inspect the existing window frame

 and repair or replace any defective or rotted wood parts. 

-AKESURETHEEXTERIORBLINDSTOPSARESOUND

B. 

Insulate the weight pocket

 with loose fill insulation. 

Note: Use of expanding/aerosol foam insulation is not recommended.

C. 

If applicable,

INSTALLPRElNISHEDMETALmASHINGORTRIMTOCOVEREXISTINGFRAMESILLANDTHE

EXTERIORTRIMATTHEHEADANDJAMBS

D. 

Clean the opening

OFANYDIRTDEBRISOREXCESSOLDPAINTBEFOREPROCEEDING

 

Note: Many windows in older homes are painted with lead-based paint. See caution note 
in Step 1.

2

 OPENING PREPARATION

*OUFSJPS
TBTITUPQ

&YUFSJPS
CMJOE
TUPQ

1BSUJOH
TUPQ

#PUUPN
TBTI

5PQTBTI

#PUUPN
TBTI
XFJHIU

5PQ
CBMBODF
DPSE

#BMBODF

DPSEQVMMFZT

5PQTBTI

XFJHIU

#PUUPN
CBMBODF
DPSET

*/5&3*03

*OUFSJPS
TBTITUPQ

1BSUJOHTUPQ

&YUFSJPS
CMJOETUPQ

E. 

Ensure existing sill is level. 

Note: If shimming of the sill is necessary, use a continuous shim that extends across the 
entire width of the sill.

Summary of Contents for V784840








Reviews: