Can
adian Comfort Industries V04
24
PELPRO OWNERS MANUAL
Copyright 2004
www.pelprostoves.com
Dansons Group Inc.
T
HE
C
ONTROLS
Basic Overview
The AcuTron II or III digital control board was designed to give you flexibility on how
you want to operate your stove. The AcuTron can be operated as a MANUAL
control or by a THERMOSTAT. When operating in the Thermostat option, you can
also choose to run your appliance in the ON/OFF mode or the LOW/HIGH mode.
The
START
or
FEED RATE
touch pad allows electricity to flow to your stove's
electrical components for 15 minutes. If after 15 minutes your stove has heated to
normal operating temperatures your stove will continue to run. If the fire does not
light and/or burn properly, the electricity to your stove's components will be shut off
at the end of 15 minutes.
The
FAN SPEED
controls the speed of the room air fan. This fan blows room air
through the heat exchange tubes and back into the room. When the
FEED RATE
is
set to a higher position, the
FAN SPEED
should be set higher and visa versa. To
achieve optimum heat transfer it is recommended to set the FAN SPEED to LOW
when running the FEED RATE at 1 or 2, and Fan on MED on FEED RATE #3 or 4.
When the
START / FEED RATE
is
ON
, the
AUGER CYCLE
LED
will turn on when
the auger is active. When the
OFF
touch pad is pushed [OFF], the auger motor will
not run, fuel stops feeding and the fire will die.
The
FEED RATE
works in a synchronized manner setting both the fuel rate and
combustion air at the same time. When fuel is increased by setting the
FEED RATE
higher, combustion air is automatically increased and visa versa.
HOW THE BOARD WORKS
I
NITIAL
START
OR
S
ET
-
UP
(M
ANUAL OR
N
ON
-T
HERMOSTAT
M
ODE
)
Upon initial start-up the control will feed automatically at the #1 feed rate.
Press the
START
touch pad.
-
Convection
(heating)
fan will start and the
FAN
LED will be solid on LOW setting
-
The 300 watt Auto-Igniter will begin to glow and the
IGNITER
LED will be solid
-
The
AUGER CYCLE
LED will go solid for 3 seconds, indicating signal is being sent to the auger motor.
-
The Combustion (exhaust) fan will start and operate at full speed for 60 seconds, then adjust downward to match
feed rate #1.
Press
FEED RATE
touch pad to select desired heat output that you require upon completion of ignition sequence.
NOTE:
If you do not press the
FEED RATE
touch pad, the stove will continue to run at FEED RATE #1 and the LED will continue
to flash at a fast rate.
When the
FEED RATE LED
is flashing at a
FAST
rate this indicates that the LOW LIMIT (L120) is closed. This means the unit
has not reached operating temperature.
When the
FEED RATE LED
is flashing at a
SLOW
rate this indicates that the LOW LIMIT (L120) is open. This means the control
board has entered a 5 minute “Safety Delay” mode.
After the 5 minute Safety Delay is complete
-
IGNITER
and INGNITER LED will turn off
-
FEED RATE
LED will become solid and the appliance will feed fuel at your selected heat output
R
E
-S
TART
(M
ANUAL OR
N
ON
-T
HERMOSTAT
M
ODE
)
The AcuTron II or III board does have limited memory. To restart your appliance push the START touch pad. The appliance will
automatically go through it normal start-up then return to the FEED and FAN setting you used prior to turning off the board and
appliance the last time of use.
as desired
as desired
