Can
adian Comfort Industries V04
28
PELPRO OWNERS MANUAL
Copyright 2004
www.pelprostoves.com
Dansons Group Inc.
I
NITIAL
A
PPLIANCE
B
URN
S
ETUP
IT IS CRITICAL FOR THE CORRECT OPERATION OF YOUR STOVE THAT THE BURN
GRATE, AIR INLET DAMPER, COMBUSTION FAN SPEED, AND
1 & 4 FUEL RATE BE SET CORRECTLY!
A
HIGH QUALITY FIRE
should burn with a brisk, yellow flame. A flame exhibiting a lazy, orange or sooty
characteristic is a poor quality and inefficient flame. A poor flame produces less heat, increases sooting and may
cause a smoky exhaust. If a poor flame exists for any period of time, clean your stove and exhaust system.
Note: if log option is purchased, do not install until initial setup is complete
START APPLIANCE AS PER LIGHTING INSTRUCTIONS
,
let stove run for approx. 10 minutes before turning the stove to the # 4 setting (or High), to
begin to make fine adjustments
. AUGER CYCLE indicator
should be lit “ON” for 3 seconds
and “OFF” for 3-5 seconds. Adjust the
AIR INLET DAMPER
. This will have to be set, as the
factory sends all units out with the damper wide open to accommodate a wide range of
installations and elevations.
AIR INLET DAMPER
:
Slide open or close
damper as needed to obtain a fire that is brisk
enough to carry ash out of the grate, but not so
brisk that it carries pellets out as well (known as
“Pop corning”). Normally you should find that the
damper will need to be closed two-thirds to three
quarters, but will vary with length of vent run, pellet
quality and elevation. The best way to set this is at
the
FUEL SETTING
#4.
When you are pleased with the burn and how the appliance is operating, you
are now ready to set the board up at LOW setting.
Set
FUEL RATE
to
#1 or LOW setting
.
Again let this burn for
approx. 10 minutes before making any adjustments. The AUGER
CYCLE indicator should be “OFF” for approx 9 – 14 seconds
between auger turnings (light ON). If “Pop corning” is taking place
at this setting adjust the
COMBUSTION FAN SPEED.
COMBUSTION FAN SPEED (Draft):
In a few instances
because of prevailing conditions pertinent to your specific
installation, or even different batches of pellet fuel, the
COMBUSTION FAN SPEED
may be adjusted to increase or
decrease the amount of air moving through the grate for the
cleanest burn. Fan speed can be adjusted by adjusting the
FAN
trim pod
COUNTER CLOCKWISE to INCREASE
the speed and
CLOCKWISE to DECREASE
the speed of the combustion fan.
FUEL RATE
:
Fuel rate at the Lowest (number 1) and highest (number 4) settings can be
changed by adjusting the
#1 or #4 TRIM PODS
located on the control panel. To
INCREASE
fuel rate turn trimmer
COUNTER CLOCKWISE
and to
LOWER
turn
CLOCKWISE
. To assist in knowing what changes you made, you
should note the amount of time the light on the
AUGER CYCLE
stays “OFF”.
(Note: The light stays “off” when ever
the fuel feed motor is not running).
Lengthening the time this light stays “OFF” lowers the fuel feed and
shortening the “OFF” time increases the fuel feed
.
Factory Setting #1 light “OFF” is approx. 9-11 seconds,
#4 light “OFF” is 3-4 seconds.
Stove Back Panel
Right Hand
Side Panel
Air Inlet
Slide Rod
Rubber
GrometT
FINE TUNE ADJUSTMENTS
1
4
FAN
Increase
Decrease
FEED RATE
START
FEED RATE
1
2
3
4
FEED RATE
START
FEED RATE
1
2
3
4
