background image

USER INSTRUCTIONS

 

Starting - up the boiler 

  Open the gas Isolation valve located under the 

boiler. 

6

7

5

4

3

2

1

8

110V   60Hz

  Switch on the boiler by placing the ON/OFF switch 

(

1

)

 

in the 

ON

 position (see “Control panel”). 

  The boiler will light automatically (with the 

WINTER mode selected and room thermostat 
connected). 

  Check that there are no flashing numbers on the 

display 

8

 (see error codes). If code 

H2O

 appears 

on the display 

8

 this denotes that there is no water 

in the boiler. Consequently, fill the system as 
described in section “Filling the system”. 

 

 

“SUMMER” mode  

To switch boiler operation to “SUMMER” mode, press 
button 

6

 (see fig. 1). The boiler will only work for the D.H.W system. The “SUMMER” mode setting of the boiler is 

signalled by the symbol

 

lit continuously on the control panel.  

Fig. 1

 

The automatic ignition system will light the burner every time there is a demand for domestic hot water. In this 

case, the symbol

 

on the control panel will flash.  

 

 

“WINTER” mode 

To switch boiler operation to “WINTER” mode, press button 

6

 (see fig. 1). The boiler will only work for the central 

heating system. The “WINTER” mode setting of the boiler is signalled by the symbol

 

lit continuously on the 

control panel. 

The automatic ignition system will light the burner every time there is a demand for room heating. In this case, the 

symbol

 

on the control panel will flash. 

 

 

“SUMMER-WINTER” mode  

To switch boiler operation to “SUMMER/WINTER” mode, press button 

6

 (see fig. 1). The boiler will work for both 

central heating/D.H.W systems. The “SUMMER/WINTER” mode setting of the boiler is signalled by the symbols 

 

 

lit continuously on the control panel. 

The automatic ignition system will light the burner every time there is a demand for room heating or domestic hot 

water, the functioning is signalled by the symbols 

 

flashing continuously on the control panel. 

 

 

Regulating the heating temperature 

The heating temperature is regulated by knob 

(see fig.1). 

  Rotating the knob counter-clockwise reduces the temperature. 

  Rotating the knob clockwise increases the temperature. 

  The range of temperature settings for the central heating runs from a minimum of 86°F to a maximum of 176°F, 

or, in the case of low temperature operation, from a minimum of 77°F to a maximum of 138°F. 

 

 

 

3

Summary of Contents for SOLENNE SERIES









Reviews: