Demo Kiosk Technical Support
For questions about the demo kiosk set up or for
additional copies of this manual, please use the
following contact information:
Thermal Solutions, Inc.
1074 Classic Drive
Apex, NC 27539
Phone: (919) 362-4575 (8 A.M. to 5 P.M. ET)
Email: mbrumsey@thermal-solutions.com
Software downloads available at:
http://www.thermal-solutions.com/customerdata/pentair/
PumpDaqSetupUS
Go to page 11 for instructions on how to install the
latest software version.
IMPORTANT WARNING AND SAFETY INSTRUCTIONS
Attention Installer: This manual contains important information about the installation, operation and safe use of this product. This information should
be given to the owner and/or operator of this equipment. Additional copies of this manual are available at:
http://www.thermal-solutions.com/customerdata/pentair/PumpDaqSetupUS/.
Before installing this product, read and follow all warning notices and in-
structions which are included. Failure to follow safety warnings and instructions can result in severe injury, death, or property damage. When installing
and using this electrical equipment, basic safety precautions should always be followed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Technical Support for IntelliFlo
®
Pump Operation
If you have questions about IntelliFlo
®
pump operation, please
use the following contact information:
Customer Service (8 A.M. to 5 P.M. — Eastern/Pacific Times)
Phone: (800) 831-7133
Fax: (800) 284-4151
Technical Support:
Sanford, North Carolina (8 A.M. to 5 P.M. ET)
Phone: (919) 566-8000
Fax: (919) 566-8920
Moorpark, California (8 A.M. to 5 P.M. PT)
Phone: (805) 553-5000 (Ext. 5591)
Fax: (805) 553-5515
Web site:
Visit www.pentairpool.com or www.staritepool.com
Pump Demo Manual Rev. C 5/15/13
© 2013 Pentair Aquatic Systems. All rights reserved. This document is subject to change without notice.
1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000
10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 553-5000
All Pentair trademarks and logos are owned by Pentair, Inc. Pentair Aquatic Systems
™
and IntelliFlo
®
are trademarks and/or registered
trademarks of Pentair Water Pool and Spa, Inc. and/or its affiliated companies in the United States and/ or other countries. Unless expressly
noted, names and brands of third parties that may be used in this document are not used to indicate an affiliation or endorsement between
the owners of these names and brands and Pentair Water Pool and Spa, Inc. Those names and brands may be the trademarks or registered
trademarks of those third parties. Because we are continuously improving our products and services, Pentair reserves the right to change
specifications without prior notice. Pentair is an equal opportunity employer.
Always disconnect power to the pump at the circuit breaker and disconnect the communication cable before servicing the pump.
Failure to do so could result in death or serious injury to service people, users or others due to electric shock. Read all servicing
instructions before working on the pump
.
To reduce the risk of injury, service should only be performed by a qualified service professional.
To reduce the risk of injury, do not permit children to use this product.
DO NOT open the strainer pot if pump fails to prime or if pump has been operating without water in the strainer pot. Pumps oper-
ated in these circumstances may experience a buildup of vapor pressure and may contain scalding hot water. Opening the pump
may cause serious personal injury. In order to avoid the possibility of personal injury, make sure the suction and discharge valves
are open and strainer pot temperature is cool to touch, then open with extreme caution
IMPORTANT! READ BEFORE TURNING ON THE PUMP
The pump can draw up to 3000 watts of power during priming and start up (typical 120V 20 Amp circuit is limited
to 1800 watts maximum). Check to be sure the pump watt and power usage does not exceed the rated capacity of
the electrical outlet.
For continued, safe operation,
the pump’s maximum speed has been set to 2800 RPM prior to shipment. It
is recommended that the maximum speed not be changed. Do not change preset maximum pump RPM without
contacting an authorized Pentair representative.
i
