13
SandShark
™
Installation and User’s Guide
Section 5
Troubleshooting
Use the following troubleshooting information to resolve possible problems with your SandShark
™
pool cleaner.
Problem
Corrective Action
I
f SandShark
™
moves slow or fails to climb walls:
Dirty filter –
Clean the filter.
Dirty basket in pump hair and lint strainer –
Clean the basket.
Debris blocking the bottom of the cleaner –
Remove the Debris.
Leaks in the hose –
Remove the leaky section.
Debris in the regulator –
Clean the regulator valve.
Low water flow through the cleaner –
Close the main drain.
If SandShark
™
doesn’t move or pulsates slowly
Make sure that the main drain and all other suction lines are closed except the suction line
or doesn’t climb pool walls properly:
to which the SandShark
™
is attached.
Check for sufficient flow through cleaner hose.
Check for debris in the filter or the pump strainer basket.
Check for debris in the SandShark’s oscillator. Debris may prevent oscillator movement
or restrict the flow through the cleaner.
Check the oscillator for: damage; lost seals (there should be 4 seals): obstructed seals
(seals should slide freely on the oscillator).
Be sure that the short, soft flexible leader hose section is the first section in the hose
assembly (next to the cleaner).
If SandShark
™
climbs pool wall to water surface
Reduce water flow through cleaner, see Adjust Flow on
page 4, 6 or 8
.
and sucks air:
To install the eyeball diverter
as follows:
A. Turn off the main circulation pump.
B. Unscrew the lock rings from the pool’s return line fittings and remove the
original
eyeball diverters.
C. Replace them with the SandShark’s eyeball diverters.
D. Replace the lock rings and tighten them. Be sure that the openings of the eyeball
diverters point down (6:00 o’clock position) or to the side (3:00 or 9:00 o’clock
positions), before fully tightening the rings.
Usually, directing the return line water flow against the side of the pool
(as described above) works best. However, you may want to try pointing the
flow downward or in different positions to see which works best in the pool.
After installing the eyeball diverter, turn the circulation pump on.
The SandShark
™
should begin moving across the pool floor, vacuuming up
the debris in its path.
E. If the SandShark’s eyeball diverters do not fit your existing return line fittings,
adjust your existing fittings as best you can as described above.
If SandShark
™
tracks in a repetitive pattern:
Check the pool return line water flow and redirect it as necessary with a return line
eyeball diverter (see above “To install the eyeball diverter”).
Check the SandShark’s hose to be sure that it has not become bent or kinked. Do not
coil the hose, as it will retain the coiled shape and reduce the cleaning coverage.
To check the hose, lay each hose section flat on the pool deck (or another flat surface)
and look down the length of the hose. It should be perfectly flat and straight. Replace any
sections which are bent or kinked.
Check the oscillator for: damage; lost seals (there should be 4 seals): obstructed seals
(seals should slide freely on the oscillator).
Be sure that the short, soft flexible leader hose section is the first section in the hose
assembly (next to the cleaner).
The water flow from the return line can push the
SandShark’s hose, causing the SandShark
™
to steer
away from the return line or to remain in one area of
the pool. To correct this, adjust your existing return
line diverters or install the eyeball diverters supplied
with the SandShark
™
cleaner:
Summary of Contents for Kreepy Krauly SandShark 7900
Page 22: ...16 SandShark Installation and User s Guide NOTES...
Page 23: ...SandShark...
Page 24: ...P N 39503 6300 Rev A 10 27 08...
