background image

figure 24: Typical mi identification tag  

(for use in hazardous areas)

 

–   mi unit reference

  is the order reference following the nomenclature 

of MI heating units (also see page 6)

–   heating Cable ref

. is the type of MI heating cable

–   element length

 is the heated length of the MI unit

–   Year of manufacture

 is the manufacturing year

–   Circuit length (if different)

 informs about the “total circuit length” in 

case of multiple elements being connected in series

–   Design Temperature Class

 states the “T-class” or “Auto Ignition 

Temperature” including the “Zone” classification, which the unit is 

designed for

–   Design method

 informs about the method of temperature control, 

which has been used for the design and must be installed to control 

the heating unit. 

 

examples: 

1) “Stabilized” indicates that the design method used is “stabilised 

design”. All parameters used in the design of the application must be 

respected in order to comply with the hazardous area requirements 

(e.g. pipe diameters, insulation thickness, process, ambient 

conditions ...). The reference temperature for the sheath temperature 

calculations is either the calculated “max. uncontrolled temperature” 

or the “max. process temperature”, whichever is higher.

2)  “Control limited” indicates that the design method used is 

“control limited design”. The reference temperature for the sheath 

temperature calculations is the control limited set point and must be 

assured by the use of an alarm capable control unit making sure the 

heating element is switched off, when the pipe/equipment exceed this 

temperature. The use of a wrong control device or a change of the 

temperature setting will invalidate the design calculation. 

3) “Limiter-Lockout” indicates that the design method used assumes 

the installation of an approved limiter (typically a safety temperature 

limiter which sensor is installed on the heating cable surface using 

an “artificial hotspot”). The set point of the limiter must be below the 

T-class of the area and may require an additional down-adjustment 

for potential falsifying of the measured temperature, refer to the 

instructions given by the manufacturer of the limiter. 

MI Unit Reference:

  

B/HSQ1M1000/43M/1187/230/2M/SC1H2.5/X/M20/EX

Heating Cable Ref.:  

HSQ1M1000 

Element Length:  

43 m

Year of Manufacture:   2006 

Circuit Length (if different):

Grade:  

  

  (high) 

Design Temperature Class:   T1   Zone1 

Design Method:    

Limiter-Lockout 

Maximum Withstand Temperature:  450°C

Max. Sheath Temperature:   331°C 

Sheath Reference Temperature:  200°C

Nom. Power Output @ 230 V:   1187 W @ Maintain Temperature

Order No:  

  

 

Customer Order No:

Batch number:    

XXXXXX 

Circuit Reference:

Type Examination No:       

Baseefa02ATEX0046X 

THIS TAG MUST NOT BE REMOVED

Follow installation and operating instructions for safe use in hazardous areas!

2 G     EEx e      T1

1180

29

Summary of Contents for Mi Series













































Reviews: