Pentair Raychem JBS-100-ECP-A Installation Instructions Manual Download

Page: 10 / 14

10 / 14

Conduit hub

Grounding strap

1/2 in lock nut

• Use the MI Cable grounding kit (ordered

separately).

• Insert the cold leads through the conduit

hub and secure.

• Add the grounding strap to the conduit hub

and then secure with 1/2 inch lock nut.

Trim

Notch

• Screw box onto stand until it stops. Do not overtighten.

• Insert cable tie through slots on stand and box, and

tighten firmly to prevent box rotation.

• Loosen locknut.
• Lift box and rotate. Make sure tab on threaded piece fits

into one of the four notches in box.

• Tighten locknut.

• Remove 1/2 in (13 mm)

plug and 1/2 in lock nut

from side of enclosure.

(Optional) to change direction of box opening:

IndustrIal Heat tracIng sOlutIOns

EN-RaychemJBS100ECPA-IM-H57463 05/16

Summary of Contents for Raychem JBS-100-ECP-A















Search results

Summary of Contents for Raychem JBS-100-ECP-A

Reviews:

Related manuals for Raychem JBS-100-ECP-A

Brands by name

Popular brands

Pentair Raychem JBS-100-ECP-A, Installation Instructions Manual

Search results

Summary of Contents for Raychem JBS-100-ECP-A

Reviews:

Related manuals for Raychem JBS-100-ECP-A

Brands by name

Popular brands