manualshive.com logo in svg

PERCo RTD-20, Manual

The PERCo RTD-20 Manual is a comprehensive guide that provides users with all the essential information they need to optimize their experience with this advanced product. Available for free download from our website, this manual ensures you have access to every detail to fully utilize the capabilities of the PERCo RTD-20.

Share
Download
background image

perco.com                  linkedin.com/mwlite/company/perco                   export@perco.com                  +7 (812) 247-04-64

   

Overall 

dimensions

Overall dimensions

Overall 

dimensions

Foundation requirements: concrete (grade 400 or higher), stone or similar foundations 

of at least 150 mm thick, when installing the turnstile on a less steady foundation, it is 

recommended to apply reinforcing elements (500х500х500 mm) or RF-20 foundation 

frame.
When using the foundation frame, hole marking and anchors are not required; in this case, 

the turnstile mounting is more secure.

Hole marking, cable duct for cable-laying, turnstile with security gate and railing section 

mounting layouts are shown in Figures.

2 holes ø25x100

24 holes ø16x60

Hole marking for turnstile mounting

RTD-20 Full height rotor turnstile

Summary of Contents for RTD-20











Reviews:

No comments

Related manuals for RTD-20

CAME GUARDIAN Installation Manual preview
GUARDIAN
Brand: CAME Pages: 80
CAME BRIDGE PSAP01 Installation Manual preview
BRIDGE PSAP01
Brand: CAME Pages: 12

Brands by name

Popular brands

Load more brands