background image

Assembly & Operation Manual 

Table 3. Pulse control mode (the jumper is set on the J1 connector) 

Indication 

The turnstile 

operating 

modes  

Actions  

to do 

on the RC 

panel 

on the LED display 

Turnstile status 

Always locked 
(Locked for entry 
and exit) 

Press the 

STOP

 

button on the 
RC panel 

The red indicator
above the 

STOP

button is on 

 

The “Red cross”  for 
each passage 
direction and “Red 
line” pictograms are on

The turnstile is locked 

Single passage in 
the set direction 
(open for 
passage of one 
person in the 
chosen direction) 

Press the 

LEFT

RIGHT

 button 

on the RC panel 

The green 
indicator above 
the button of the 
chosen 
passage 
direction 

«Left»

«Right»

 is on  

The “Green arrow” 
and “Dynamic green” 
pictograms in the 
chosen passage 
direction are on  

When the passage is 
completed, the 
turnstile is locked 

Bi-directional 
single passage 
(open in both 
directions for 
‘one-by-one’ 
passage) 

Press both the 

LEFT

 and 

RIGHT

 buttons 

on the RC panel 
simultaneously  

The two green 
indicators 
(

«Left»

 and 

«Right»

) are on 

The “Green arrow” 
for each passage 
direction and “Green 
line” pictograms are 
on. After the 
passage in the 
chosen direction the 
“Red cross” is on for 
that direction. After 
the passage in both 
directions the “Red 
line” is on.  

The turnstile is locked 
in the direction of 
completed passage 

Free passage in 
the set direction 
(open for free 
passage in the 
chosen direction) 

Press the 

STOP

 

button and the 
button 
corresponding to 
the chosen 
passage 
direction 

LEFT

RIGHT

 

simultaneously  

The green 
indicator above 
the button of the 
chosen 
passage 
direction 

«Left»

«Right» 

is on  

The “Green arrow” in 
the chosen passage 
direction and “Green 
line” pictograms are 
on.   

Turnstile remains 
open in the set 
direction 

Free passage in 
the set direction 
and single 
passage in the 
opposite direction 
(open for free 
passage in the 
chosen direction 
and for passage 
of one person in 
the opposite 
direction) 

 Set the “

Free 

passage in the 
set direction” 

mode for one 
direction and 

Single passage 

in the set 
direction”

 for the 

other.  

The two green 
indicators 
(

«Left»

 and 

«Right»

) are on. 

The “Green arrow” 
for each passage 
direction and “Green 
line” pictograms are 
on. After the single 
passage the “Red 
cross” is on.   

After the passage in 
the free passage 
direction the turnstile 
remains open in both 
directions. After the 
passage in the single 
passage direction the 
turnstile remains open 
in the free passage 
direction but it gets 
locked in the single 
passage direction 

Always free (open 
for entry and exit) 

Press all the 3 
buttons on the 
RC panel 
simultaneously: 

LEFT

STOP

 

and 

RIGHT

 

The two green 
indicators 
(

«Left»

 and 

«Right»

) are on

 

The “Green arrow” 
for each passage 
direction and “Green 
line” pictograms are 
on. 

The turnstile remains 
open 

24 

Summary of Contents for TTR-08A



































Reviews:

Related manuals for TTR-08A