manualshive.com logo in svg

PERCo TTR-10A Series, Assembly And Operation Manual

The PERCo TTR-10A Series offers innovative access control solutions. Ensure a smooth operation and hassle-free assembly with our comprehensive "Assembly And Operation Manual." Download this essential manual for free at 88.208.23.73:8080 to unlock the full potential of your PERCo TTR-10A Series product.

Share
Download
background image

TTR-10A electromechanical tripod turnstile  

Installation tools: 

M8×25 screws with spring washers for mounting the hub ........................................................... 3 
Anaerobic adhesive sealant for fixing the hub screws (20 ml)

 

.................................................... 1 

SW3 Allen key  ............................................................................................................................. 1 
100 mm cable ties  ....................................................................................................................... 5 
M8 nuts

 

........................................................................................................................................ 4 

Flat washers

 (

8) ........................................................................................................................... 4 

Spring washers (8)

 

...................................................................................................................... 4 

Technical documentation: 

Certificate .................................................................................................................................... 1 
Assembly and operation manual  ................................................................................................. 1 

4.1.2 

TTR-10AK 

modification  

Package: 

Box .............................................................................................................................................. 1 

Basic equipment: 

Turnstile housing and base assembled ....................................................................................... 1 
Hub with barrier arms  .................................................................................................................. 1 
RC-panel with cable

 

.................................................................................................................... 1 

Box with a 

MT10.2 

mounting bracket 

(Fig. 15), includes: 

Assembled bracket ...................................................................................................................... 1 

Installation tools: 

M8×25 screws with spring washers for mounting the hub ............................................................3 
Anaerobic adhesive sealant for fixing the hub screws (20 ml)

 

.................................................... 1 

SW3 Allen key

 

............................................................................................................................. 1 

100 mm cable ties  ....................................................................................................................... 5 
M8 nuts

 

........................................................................................................................................ 4 

Flat washers

 

(8) ........................................................................................................................... 4 

Spring washers (8)  ...................................................................................................................... 4 

Technical documentation: 

Certificate .................................................................................................................................... 1 
Assembly and operation manual  ................................................................................................. 1 

4.1.3 

TTR-10AB 

modification  

Package: 

Box

 

.............................................................................................................................................. 2 

Box #1 includes: 

Basic equipment: 

Turnstile housing and base assembled

 

....................................................................................... 1 

Hub with barrier arms  .................................................................................................................. 1 
RC-panel with cable  .................................................................................................................... 1 

Installation tools: 

M8×25 screws with spring washers for mounting the hub

 

........................................................... 3 

Anaerobic adhesive sealant for fixing the hub screws (20 ml)

 

.................................................... 1 

SW3 Allen key

 

............................................................................................................................. 1 

100 mm cable ties  ....................................................................................................................... 5 
M8 nuts ........................................................................................................................................ 4 
Flat washers (8) ........................................................................................................................... 4 
Spring washers (8)  ...................................................................................................................... 4 

Technical documentation: 

Certificate .................................................................................................................................... 1 
Assembly and operation manual  ................................................................................................. 1 

Box #2 includes: 

MT10.3 

mounting post assembled for floor mount (Fig. 16) ............................................................ 1 

5 

Summary of Contents for TTR-10A Series



































Reviews:

No comments

Related manuals for TTR-10A Series

Brands by name

Popular brands

Load more brands