Perfect Aire 4PADP95, User Manual

3

CONTROL PADS ON THE DEHUMIDIFIER

NOTE: 

The control 

panel of the unit 

you purchased 

may be slightly 

different according 

to the models.

Bucket Full

Indicator Light

Auto Defrost ON 

Indicator Light

6                                                   

7

9

10

1

2

4

5

3

2

TIMER

8

On

Off

Defrost Full

CONT.

POWER

PUMP COMFORT FILTER

TURBO

ION

CONTROL PADS: 

When you push the button to change 

operation modes, the unit will make a single “beep” 

sound to indicate that it is changing modes.

  1. POWER 

–

Press to turn the dehumidifier on and off.

   2.  / : UP/DOWN PADS / HUMIDITY SET CONTROL PADS

 • 

The humidity level can be set within a range  

of 35%RH to 85%RH (Relative Humidity) in  

5% increments.

 • 

For drier air, press the   pad and set to a lower 

percent value (%).

 • 

For damper air, press the   pad and set a higher 

percent value (%).

 • 

The recommended standard setting is 45-50%. 

You must be on Normal mode to set the humidity

 • 

Cannot be used on COMFORT or CONT. mode.

  3. DISPLAY 

Shows the set % humidity level from 35% to 85% 

or auto on/off time (0-24) while setting, then  

shows the actual ( +/- 5% accuracy) room % 

humidity level in a range of 30%RH to 90%RH 

(Relative Humidity).

  4. TIMER 

–

Press to initiate the Auto on and Auto off 

feature, in conjunction with the   and   key pads. 

Timer range is 0.0 – 24 hrs. Timer does not cycle. 

Indicator(s) above the button ("On" and/or "Off") 

will illuminate when the operation is active.

 5. CONTINUOUS (CONT.) 

–

Press to activate the 

continuous dehumidifying operation. When 

operating in this mode the UP/DOWN  / pads 

will be deactivated and you will NOT be able to 

set a desired humidity. The unit will run non-stop 

unless using the bucket to collect water. At which 

point, the unit will shut off when the bucket is full. 

Indicator above the button will illuminate when the 

operation is active.

  6. PUMP 

–

Press to activate the pump operation. 

NOTE: Make sure the pump drain hose is installed 

into the unit and the continuous drain hose is 

removed from the unit before the pump operation 

is activated. When the bucket is full, the pump 

will initiate. Refer to the next pages for removing 

the collected water. Do not use this operation 

when the outdoor temperature is equal to or less 

than 32ºF (0ºC). Indicator above the button will 

illuminate when the operation is active.

 7. COMFORT 

–

Utilize this dehumidification feature to 

automatically keep humidity in the 45%–55% 

range based on room temperature. When 

operating in this mode the UP/DOWN  /  pads 

will be deactivated and you will NOT be able to set 

a desired humidity. Indicator above the button will 

illuminate when the operation is active.

  8. FILTER 

–

The check filter feature is a reminder to 

clean the Air Filter for more efficient operation. 

The “Filter” light (Clean Filter Indicator Light) will 

illuminate after 250 hours of operation. To reset 

after cleaning the filter, press and hold the Filter 

button and the light will go off, resetting the timer. 

Indicator above the button will illuminate when the 

operation is active.

  9. TURBO 

–

Press to select Turbo fan speed for 

maximum moisture removal. When the humidity 

has been reduced and quiet operation is preferred, 

set the fan control to Normal by pressing the 

TURBO pad to turn off Turbo fan/light. Indicator 

above the button will illuminate when the 

operation is active.

 10. ION 

–

Press to activate the ionizer. Negatively 

charged ions (anions) are automatically generated 

by ionization. These ions deactivate airborne 

chemical vapors and dust particles. Press the pad 

again to stop the function. Indicator above the 

button will illuminate when the operation is active.

 NOTE: 

When not in COMFORT or CONT. mode, the 

unit operates in NORMAL mode. Utilize this mode 

if you would like the unit to cycle on and off based 

on the relative humidity setting you have manually 

selected. (See numbers 2 and 3 above.) In 

NORMAL mode, both the “Comfort” and “Cont.” 

Indicator lights will not be illuminated.

FIG. 1