4
ERROR AND PROTECTION CODES
AS – HUMIDITY SENSOR ERROR
Unplug the unit for at least 5 minutes and plug
it back in. Make sure the filter is clean. If error
repeats, call Perfect Aire Consumer Services at
844.472.2473.
ES – TEMPERATURE SENSOR ERROR
Unplug the unit for at least 5 minutes and plug
it back in. Make sure the filter is clean. If error
repeats, call Perfect Aire Consumer Services
at 844.472.2473.
P2 – BUCKET IS FULL OR NOT IN THE CORRECT POSITION
Empty the bucket and replace it in the proper
position. Ensure float switch and foam are
secured properly in bucket.
E3 – UNIT MALFUNCTION
Unplug the unit for at least 5 minutes and plug
it back in. If error repeats, call Perfect Aire
Consumer Services at 844.472.2473.
EC – BUCKET IS REMOVED OR NOT IN RIGHT POSITION
Replace bucket in the right position.
OTHER FEATURES
BUCKET FULL INDICATOR LIGHT
Illuminates when the bucket needs to be emptied, is
removed, or is not placed in the proper position.
AUTO SHUT OFF
The dehumidifier shuts off after 30 seconds when the
bucket is full or when the bucket is removed or not
replaced in the proper position. When the humidity
setting is reached, the unit will cycle off automatically.
(The compressor cycles off first. 3 minutes later, the fan
will turn off as well.)
AUTO DEFROST
When frost builds up on the evaporator coils, the
compressor will cycle off and the fan will continue to
run (on “Turbo”) until the frost disappears. The AUTO
DEFROST Indicator light will illuminate. The unit will
restart on its own once the auto defrost process
has completed.
SAFETY FEATURE
After the unit has stopped, it cannot resume operation
within in the first 3 minutes. This is to protect the unit.
Operation will restart automatically after 3 minutes.
CHECK FILTER FEATURE
The system starts to log the time once the fan motor
operates. The check filter light will be lit up only when
the accumulated operation time achieves 250 hours or
more. The CLEAN FILTER Indicator light flashes once
every second. After cleaning the air filter, press and hold
the FILTER button to reset the filter timer and turn off
the CLEAN FILTER indicator light.
AUTO-RESTART
If the unit breaks off unexpectedly due to a loss of
power, it will automatically restart with the previous
function setting when the power resumes.
SETTING THE TIMER
• When the unit is on, press the TIMER button; the
TIMER OFF indicator light illuminates, indicating that
the Auto Stop program is initiated. Press it again and
the TIMER ON indicator light illuminates indicating
that the Auto Start program is initiated.
• If you prefer, you can set the timer while the unit is
powered off and follow the instructions above to set
the unit to go on and then off.
• Press or hold the UP or DOWN pad to change the
Auto time by 0.5 hour increments, up to 10 hours,
then at 1 hour increments up to 24 hours. The
display on the control pad will count down the time
remaining until start/stop.
• The selected time will register for 5 seconds and the
system will automatically revert back to displaying
the previous humidity setting.
• When the Auto start and Auto stop times are set
within the same program sequence, TIMER ON and
OFF indicator lights illuminate, identifying both ON
and OFF times are now programmed. You can set the
Timer for just ON or just OFF in which case the single
corresponding ON or OFF light will be illuminated.
• Turning the unit ON or OFF at any time or
adjusting the timer setting to 0.0 will cancel the
Auto Start/Stop.
• When LED display window displays the code of P2,
the Auto Start/Stop function will also be canceled.
A NOTE ABOUT THE TIMER:
When you set the timer, the unit will only go on once
and off once. If you want the dehumidifier to cycle on
and off repeatedly, you do not need to set the timer.
Instead, set your desired humidity and the unit will cycle
on and off based on the selected humidity setting.
Summary of Contents for 4PADP95
Page 15: ...12...
