background image

DIGITAL AUTOMOTIVE 

MULTIMETER

OWNER'S MANUAL

Stock Number W2972/W2969

FOR YOUR SAFETY,

please read these instructions carefully and retain them for future use.

     WARNING!

It is the owner and/or operators’ responsibility to study all WARNINGS, operating, and maintenance instructions contained 

on the product label and instruction manual prior to operation of this product. The owner/operator shall retain product 

instructions for future reference.
The owner and/or operator are responsible for maintenance, maintaining all decals or warning labels and while in use, 

maintaining the unit in good working order. If the owner and/or operator are not fluent in English, the product warnings and 

instructions shall be read and discussed with the operators’ native language by the purchaser/owner or his designee. 

Make sure that the operator comprehends its contents. Safety information shall be emphasized and understood prior to 

usage. The product shall be inspected per the operating instructions.
Users of this product must fully understand these instructions. Each person operating this product must also be of sound 

mind and body and must not be under the influence of any substance that might impair their vision, dexterity or judgment.
Protect yourself and others by observing all safety information.
Failure to comply with instructions could result in personal injury and/or property damage! 

If you encounter any problems or difficulties, please contact our customer service department at: 1-800-426-1262 between 

6:30 a.m. and 4:30 p.m. Pacific time. 

Due to continuing improvements, actual product 

may differ slightly from photo shown.

Summary of Contents for W2969

















Reviews: