Read these safety warnings before operation.
WARNING!
Failure to heed these warnings may result in loss of load, dam-
age to jack, and/or jack failure resulting in personal injury or
property damage.
WARNING!
This is a lifting device only. Load must be supported immedi-
ately by Jack Stands.
Do not overload jack beyond rated capacity. Overloading can
cause damage to or failure of the jack.
REFER TO YOUR VEHICLE OWNERS MANUAL FOR PROPER
JACKING PROCEDURES. Lift only on areas of the vehicle as
specified by the vehicle manufacturer.
This jack is designed for use only on hard level surfaces capa-
ble of sustaining the load. Use of jack on other than hard level
surfaces can result in jack instability and possible loss of
load.
Be sure all personnel are clear of load before lowering load.
Ensure that no personnel pass underneath load until load is
securely supported by jack stands.
Specifications are subject to
change without notice
IMPORTANT SAFETY INFORMATION
Figure 5
TROUBLESHOOTING
Your Performance Tool hydraulic jack was constructed with quality
materials and workmanship and will give you many years of trouble free
use when cared for as described in the "Care & Maintenance" section
on page 3. However, as with any mechanical device, periodic adjust-
ments are necessary to maintain a peak level of performance. Should
your jack be displaying any of the following symptoms, the simple pro-
cedures shown below will correct the problem.
Will not lift load
Will not hold load
Will not lift to full height
Pump feels "spongy" under load
Handle raises under load
Handle lowers under load
Valves may not
be closing
completely.
To seat valves:
a.) Close
release valve.
b.) With jack in
fully lowered
position,
manually raise
ram/extension
screw assy. as
high as
possible.
c.) Open release
valve and
allow jack
to descend
to lowered
position.
Power unit may
be low on fluid.
With jack on level
surface and in
down position,
remove filler plug
and add clean
hydraulic jack
fluid to level of
filler hole.
Power unit may
be airbound.
Open the release
valve a minimum
of 2 full turns.
Pump the handle
a minimum of 20
full strokes to
purge air from
the system.
NOTE:
Problems listed above with more than one solution may have a combination of causes.
Please be sure that all solutions listed for each problem have been checked to eliminate
possibility of further trouble. Sometimes solutions may need to be repeated for best results.
WARNING - Remove jack from service before making adjustments
Oil Filler Port
Check & fill
oil here.
Oil must be
level with
bottom edge
of port.
REPLACEMENT PARTS
Part #
Description
Qty.
Part #
Description
Qty.
*Included in Repair Kit, stock number W1636CK
Parts List
Figure 4
24
9
10
8
7
5
11
17
19
20
16
15
13
12
2
1
2
3
4
18
23
24
2
6
23
14
SPECIFICATIONS
Capacity: .................. 60,000 lbs.
Low Height: ..................... 11-1/4"
Max. Height: ................... 18-1/4"
1 W1636-1
Hydraulic Unit Body
1
2 W1636-2
6 mm Steel Ball*
3
3 W1636-3
Release Valve O-Ring*
1
4 W1636-4
Release Valve*
1
5 W1636-5
Flat Washer*
1
6 W1636-6
Pump Cylinder
1
7 W1636-7
Pump Piston O-Ring*
1
8 W1636-8
Pump Piston Back-up Ring* 1
9 W1636-9
Pump Piston*
1
10 W1636-10 Handle Socket Assembly
1
11 W1636-11 Filter Screen*
1
12 W1636-12 Cylinder Seal*
1
13 W1636-13 Cylinder
1
14 W1636-14 O-Ring*
1
15 W1636-15 O-Ring Retainer*
1
16 W1636-16 Ram Assembly
1
17 W1636-17 Reservoir
1
18 W1636-18 Oil Filler Plug*
1
19 W1636-19 O-Ring*
1
20 W1636-20 Top Nut
1
21 W1636-21 Pump Handle Set
1 Set
